User manual DOLMAR ES-2145 A

[. . . ] Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations!Keep this instruction manual! ES-2130 A ES-2135 A ES-2140 A ES-2145 A http://www. dolmar. com Thank you for your trust in our product We congratulate you on your new DOLMAR electric chain saw. We are convinced that you will be satisÞed with this modern machine. DOLMAR electric chain saws are characterized by their robust, high-efÞciency motors and high chain velocities which allow an excellent cutting efÞciency. [. . . ] Do not use the saw if the ON/OFF switch is defective. Have it repaired by a qualiÞed person. Observe the accident prevention instructions issued by the competent trade federations and insurance companies. Do not perform any modiÞcations on the electric chain saw. Perform only the maintenance and repair works described in the instruction manual. All other works must be carried out by the DOLMAR service. Use only original DOLMAR spare parts and accessories. Applying spare parts which are not original DOLMAR parts or accesories and bar/chain combinations or lengths results in a high risk of accidents. For accidents and damage resulting from using sawing devices or accesories which have not been approved we cannot accept any responsibility. For the event of a possible accident, please, make sure that a Þrst aid box is always immediately available close by. Immediately replace any items used from the Þrst aid box. Should you ask for help, please, give the following information: - place of accident - what happened - number of injured persons - kind of injuries - your name. NOTE Individuals with poor circulation who are exposed to excessive vibration may experience injury to blood vessels or the nervous system. Vibration may cause the following symptoms to occur in the Þngers, hands or wrists: "Falling asleep" (numbness), tingling, pain, stabbing sensation, alteration of skin colour or of the skin. If any of these symptoms occur, see a physician! 8 - - - 20 Maintenance - - 21 - 22 First aid SERVICE 23 24 Technical data Power consumption Nominal voltage Mains frequency Nominal current Fuse, electric circuit Cable length Chain type Chain pitch Length of a cut Max. chain speed per EN 60745-2-13 ES-2130 A Watt V Hz A A cm inch cm m/s dB (A) ES-2135 A 2000 230 - 240 ~ 50 - 60 8, 8 16 30 / 500 092 3/8" ES-2140 A ES-2145 A 30 35 13, 3 101, 8 90, 8 40 45 Sound power level LWA av Sound pressure level LpA av dB (A) at the workplace per EN 60745-2-13 Vibration acceleration ah, w av per EN 60745-2-13 - Tubular handle m/s2 - Rear handle m/s2 Oil pump Oil tank capacity ml Power transmission Overload protection Chain brake Run-out brake Weight (without bar/chain) kg kg Weight (with bar/chain) Radio interference suppression / EMC Protective case Extension cable (not included) 5, 0 4, 7 5, 6 automatic 140 direct electrical manually actuated electrical 4, 4 5, 1 5, 2 Per EMC Directive 2004/108/EG class II (double protective insulation) DIN 57282/ HO 7RN-F L= 30 m max. , 3x1, 5 mm2 5, 3 1 Denomination of components 2 3 Figure: IdentiÞcation plate ES-2145A 2008 123456 Serial number Year of manufacture 7 6 5 4 230-240 V~ 50-60 Hz 8. 8 A 2000 W GB Typ 226 XXX XXX XXX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Tubular handle Hand guard (release for chain brake) Spike bar Sprocket guard quick tightener Sprocket guard, chain brake Carbon brush cover Back hand guard Power cord with plug Guide bar Oil tank cap IdentiÞcation plate Locking button Rear handle Power switch Sightglass for oil level Saw chain Cord grip for electric cord (pull relief) 8 Indicate when ordering spare parts! 9 10 11 12 13 17 16 15 14 9 PUTTING INTO OPERATION CAUTION: When working on the guide bar or saw chain always wear protective gloves and pull out the power supply plug. CAUTION: Switch on the electric chain saw only after having assembled it completely and inspected! A Mounting the guide bar and saw chain Put the electric chain saw on a stable surface and carry out the following operations for mounting the bar and chain: Release chain brake. To do this, pull the hand guard (1) in the direction of the arrow. 1 4 Flip up the sprocket guard quick tightener (2) (see also Fig. Push in the sprocket guard quick tightener Þrmly against spring pressure, and slowly turn it counter-clockwise until you feel it engage. Keep pushing in, and turn it as far as possible counter-clockwise. Release the sprocket guard quick tightener (remove pressure) and now turn it clockwise to its original position. Repeat this procedure until the sprocket guard (3) is unscrewed. [. . . ] Use of guide bar and saw chain lengths which have not been approved. Use of force, improper use, misuse or accidents. Damage caused by overheating due to dirt obstructing the cool air supply at the motor case. Use of unsuitable spare parts or parts which are not original DOLMAR parts, as far as they have caused the damage. [. . . ]