User manual DOLMAR TM-98.14 H2D PARTS LIST 2007-02

[. . . ] For the components listed under PARTS COVERED, the service dealer authorized by DOLMAR will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U. EMISSION COMPONENT DEFECT WARRANTY PERIOD The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years. PARTS COVERED Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement point for that part. [. . . ] Keep the chain, bar and sprocket clean and lubricated; replace worn sprockets or chains. You can spot a dull chain when easy-to-cut wood becomes hard to cut and burn marks appear on the wood. Tighten all nuts, bolts and screws except the carburetor adjustment screws after each use. Keep spark plug and wire connection tight and clean. Store saws in a high or locked place, away from children. Only properly trained professionals should work in an area where the logs, limbs and roots are tangled (i. Drag the logs into a clear area before cutting. 1 Handle 2 Filter cover 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muffler with spark arrester screen 7 Spike bar (toothed stop for holding saw steady against wood) 8 Chain tensioning screw 9 Retaining nuts 10 Chain catch 11 Sprocket guard 13 Adjusting screws for carburetor 12 Adjusting screw for oil pump (bottom side) 16 Starter grip 17 Combination switch (Choke / Start / Stop) 18 Throttle lever 19 Safety locking button 20 Rear hand guard 21 Fuel tank cap 22 Fan housing with starting assembly 23 Oil tank cap 24 Guide bar 25 Chain (Blade) Power at speed Max. Engine speed with bar and chain Idling speed Coupling speed Sound Pressure Level at the operator`s ear at full load according to ANSI B 75. Sound Pressure Level at the bystander`s position (50 ft/5 m distance) according to ANSI B 75. Load per ISO 7293 Fuel tank capacity Chain oil tank capacity Mixture ratio (fuel/two-stroke oil) - when using DOLMAR High Performance oil - when using other synthetic oils Chain brake Sprocket pitch Number of teeth Chain type Pitch / gauge Guide bar, length of a cut Guide-bar type Weight (fuel tank empty, without chain, guide bar and accessories) cu. Raise the tip of the guide bar a little and turn the chain tensioning screw (4) to the right (clockwise) until the saw chain is again up against the bottom edge of the guide bar (see circle). While keeping the tip of the guide bar raised, tighten the nuts (2) again with the universal wrench. If kickback occurs due to contact of the guide-bar tip with wood (see SAFETY PRECAUTIONS, page 10), the chain brake will stop the chain through inertia if the kickback is sufficiently strong. The chain brake is installed to block the saw chain before starting it and to stop it immediately in case of an emergency. IMPORTANT: NEVER run the saw with the chain brake activated (except for testing, see "Testing chain brake")!Doing so can very quickly cause extensive engine damage!ALWAYS release the chain brake before starting the work!To engage the chain brake manually, simply push the hand guard (1) forward (towards the tip of the saw) with your left hand (arrow ). Pull the hand guard (1) towards you (arrow 2) until you feel it catch. If the kickback is strong enough the sudden acceleration of the guide bar combined with the inertia of the hand guard (1) will automatically actuate the chain brake. Be especially careful when handling gasoline (petrol). [. . . ] In case of damage, have repaired by a qualified service center immediately Demount, clean and oil slightly Clean the guide groove of the guide bar Empty and clean Run empty 32 30 24, 30 27 17, 35 35 33 33 35 20 35 Every 3 months Annually Storage The maintenance and repair of modern engines as well as all safety devices require qualified technical training and a special workshop equipped with special tools and testing devices. The DOLMAR service centers have all the necessary equipment and skilled and experienced personnel, who can work out costeffective solutions and advise you in all matters. Any work not described in this Manual may be performed only by a DOLMAR service center. Reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used. [. . . ]