User manual DOMETIC MSP 2024

[. . . ] Persons (including children) whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely should not use this appliance without initial supervision or instruction by a responsible person. do not operate the device in a damp or wet environment. Do not operate the device near any flammable materials. Do not operate the device in areas that are potentially explosive. [. . . ] Element Main switch 0 / Off: device is switched off I / On: device is switched on II / Remote: Device can be turned on and off with an external switch or controlled with a remote control (accessory) 2 3 4 5 No. Element DIP switch for switching to energy-saving mode Fuse 230 VAC input jack 230 VAC output jack Earth terminal Remote Port II for connecting a remote control (accessory) Remote Port I for connecting to an external switch, for turning the device on and off DC terminal (positive pole) DC terminal (negative pole) 2 4, page 4) The "Input Level" LED shows the present range of the input voltage. 2 3, page 4) The "Load Level" LED shows the power presently being supplied by the inverter. Display Orange, constantly lit Orange, slowly flashing Green, constantly lit Red, quickly flashing Red, slowly flashing Red, occasionally flashing Red, constantly lit Input voltage Normal operation with battery power supply Energy-saving mode external supply via 230 VAC voltage Input voltage too high Input voltage too low Overheating Excessive load You can fasten the inverter using the holders supplied. When selecting the installation location, observe the following instructions: The inverter can be mounted horizontally or vertically. The inverter must be installed in a place that is protected from moisture. A ventilation system must be present for installations in small, closed spaces. The minimum clearance around the inverter must be at least 25 cm. The air intake on the underside or the air outlet on the back side of the inverter must remain clear. For ambient temperatures higher than 40 °C (such as in engine or heating compartments, or direct sunlight), the heat from the inverter under load can lead to the automatic shut-off of the inverter. The installation surface must be level and sufficiently strong. You must be able to support the weight of the inverter. Make sure you have adequate space for the cable connections underneath the device when choosing a mounting location. Note With the cable socket, you can secure the connection cable to the back side of the device. After running the cable, secure it with cable ties to the clips on the cable socket. Caution Before drilling any holes, ensure that no electrical cables or other parts of the vehicle can be damaged by drilling, sawing and filing. Fastening the inverter horizontally Clip two holders on the left bar and two on the lower right bar (fig. 5 1, page 5) with the clip over the edge on the back side of the inverter (fig. Screw the cable socket on with one screw in each of the four holes. Fastening the inverter vertically Clip two holders on the left bar and two on the lower right bar (fig. 6 1, page 6) on to the wall with one screw in each of the four holes. 6 2, page 6) onto the cable socket, so that the edge on the back of the inverter is pinched between the wall and the clip on the cable socket. [. . . ] Rated input voltage Output power Peak output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight Rated input voltage Output power Peak output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight 8. Rated input voltage Output power Peek output power Output voltage Output frequency Idle current consumption Standby current consumption Input voltage range Efficiency up to Ambient temperature for operation Ambient temperature for storage Dimensions W x D x H Weight 2. Elément Interrupteur DIP pour le réglage du mode d'économie d'énergie Fusible Douille d'entrée 230 VCA Douille de sortie 230 VCA Borne de masse Port à distance II pour le raccordement d'une télécommande (disponible en accessoire) Port à distance pour le raccordement d'un commutateur externe permettant d'allumer et d'éteindre l'appareil. Enfichez le raccordement de la télécommande uniquement dans le port à distance II et pas dans le port à distance I. [. . . ]