User manual DOMETIC PENGUIN AC INSTALLATION

[. . . ] 620515, 620525, 620526, 630515 & 630516 Installation Instructions RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Date Purchased MODEL 620515, 620525, 620526 Roof-Top Air Conditioner 630515, 630516 Roof Top Heat Pump used with one of following: 3105007 Return Air Cover 3105935 Quick Cool Return Air Cover 3308120 Genesis Air Filtration System and 3109228. 001 (White) Comfort Control CenterTM 3109228. 019 (Black) Comfort Control CenterTM THIS UNIT IS DESIGNED FOR OEM INSTALLATION ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE SALES DEPT. USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center Assistance Call: 800-544-4881 C US This manual must be read and understood before installation, adjustment, service, or maintenance is performed. This unit must be installed by a qualified service technician. Modification of this product can be extremely hazardous and could result in personal injury or property damage. Lire et comprendre ce manuel avant de procéder à l'installation, à des réglages, de l'entretien ou des réparations. L'installation de cet appareil doit être effectuée par un réparateur qualifié. [. . . ] This box contains mounting hardware for the air conditioner and will be used inside the RV. Minor adjustments can be done from the inside of the RV if required. 9 620515, 620525, 620526, 630515 & 630516 Installation Instructions G. Installing The Air Conditioner Installing Unit with 3105007 or 3105935 Return Air Kit. For unit with Genesis Air Filtration System, see page 11. 12 Divider Plate Ceiling Template Return Air Cover e. Install the Romex connector in the junction box. Hold the ceiling template up to the 14-1/4" x 14-1/4" (±1/8") opening. Be sure the large plate faces the rear of the RV. Start each mounting bolt through the ceiling template and up into the unit base pan by hand. Install wood screw in each end of the ceiling template. This insures a tight fit of the return air cover to ceiling. Evenly tighten mounting bolts to compress gasket to 1/2" this will be a torque of 40 - 50 inch pounds. The bolts are self locking so over tightening is not necessary. 15 Front of Vehicle Roof Gasket Return Air Grill 1. Check gasket alignment of the air conditioner over the roof opening and adjust if necessary. Unit may be moved from below by slightly lifting and moving. 13 Center Unit From Below Screws Tighten to compress gasket to 1/2" Finger Tight CAUTION Roof Gasket b. Remove return air cover and ceiling template from the 3105007 or 3105935 carton. Locate the four (8" x 1/4- 20) unit mounting bolts, junction box cover and Romex connector in the 3107180 bolt kit. Pull down the unit's electrical cord and fasten the junction box with screws to the framing in the front of the 14-1/4" x 14-1/4" (±1/8") opening. 14 DC Power Furnace Unit CCC Connectors Gasket If bolts are left loose there may not be adequate roof seal or if over tightened, damage may occur to the air conditioner base or ceiling template. Tighten to specifications listed in this manual. 2. [. . . ] Use only a small flat blade screw driver (wider than the dip switch slot) to move the dip switch. Heat strip selection: Units with a heat strip, the #1 dip switch will be in the "ON" position. Furnace selection - when a furnace has been connected to a zone, place the furnace dip switch "ON" for that zone. d. Differential - differential is the temperature difference between the "ON/OFF" cycle of the thermostat in the furnace mode. [. . . ]