User manual DOMETIC SLIDE TOPPER INSTALLATION

[. . . ] It is not waterproof, some drips, condensation, or wind blown precipitation can be present under the canopy. Product features and specifications as described or illustrated are subject to change without notice. Installation methods not described in this manual must have written approval from Dometic Corporation. RECOGNIZE SAFETY INFORMATION ! This is the safety-alert symbol. When you see this symbol in this manual, be alert to the potential for personal injury. [. . . ] 5. 25 inch Max. Slide-Out Room Flange or Facing 0. 74" Mounting Bracket Side Flange of Room FIG. 2 Mounting Bracket Position Bracket adjacent to top and side flanges as shown. FIG. 3 Mounting Bracket (Kit # 3106992. X39X, . X54X & . X62X) Awning Rail Top Flange of Room 6" Min. 5. 25 inch Max. Slide-Out Room Flange or Facing 1. 24" Mounting Bracket Side Flange of Room Mounting Bracket Position Bracket adjacent to top and side flanges as shown. 4 Slide Topper Installation & Operating Instructions FIG. 4 Mounting Bracket (Kit # 3106992. X47X, . X70X, 088X & 096X) Awning Rail Top Flange of Room 4" Min. 3. 5" Max Slide-Out Room Flange or Facing 1. 24" Mounting Bracket Position Bracket adjacent to top and side flanges as shown. Z-Clip Mounting Bracket Side Flange of Room When installing the A&E model Slide-Topper on vehicles with extra large slide-out room flanges, it may be necessary to install the mounting bracket directly on the flange. 5 & 6. The bracket must only be mounted on the flange where there is sufficient backing material or framing behind the flange. FIG. 6 5 Slide Topper Installation & Operating Instructions OPTIONAL 3107940. 003 SPACER KIT Used when Slide-out flange has a large curve or is recessed behind the main wall of vehicle. SOME INSTALLATIONS MAY REQUIRE USE OF SPACER KIT 3107940. 003 FIG. 8 SOME INSTALLATIONS MAY REQUIRE USE OF SPACER KIT 3107940. 003 SIDE WALL WITH RECESSED SLIDE-OUT SHOWN FIG. 7 3106992. 039X BRACKET SHOWN 3106992. 047X BRACKET SHOWN 0. 75" SPACER KIT SHOULD ALSO BE USED WHEN SLIDE-OUT ROOM WALL LIES BEHIND MAIN WALL OF VEHICLE 1. 24 0. 75" SPACER KIT SHOULD ALSO BE USED WHEN SLIDE-OUT ROOM WALL LIES BEHIND MAIN WALL OF VEHICLE 1. 24" PREPARATION: Unpack the awning and check the contents against the following parts list: (2) 308171. 022 Pop Rivet (3/16" x 3/8") *730099-(X) Awning Rail - Required *3107216. 008 Screw, Awning Rail, S 6-20 x 0. 50" Sq Dr **(1) 3106992. X21(X) Std Wall Brkt W/Anti-Billow **(1) 3106992. X39(X) Offset Wall 60° Brkt W/Anti-Billow **(1) 3106992. X47(X) Offset Wall 90° Brkt W/Anti-Billow **(1) 3106692. X70(X) Offset Wall 90° Brkt W/Anti-Billow (1) 3106992. 088(X) Offset Wall 90° W/Steel Hex Bars & Anti-Billow (1)3106992. 096(X) Offset Wall 45° W/Steel Hex Bars & Anti-Billow *(2) 3309962. 003(X) Bracket Spacer NOTE: Replace (X) with color letter code B = Polar White H = Mende S = Satin R = Champagne U = Black V = Gold * Not included with all models ** Not included but one of the 3 options required. INSTALLATION INSTRUCTIONS ASSEMBLE EXTENSION 2. Rivet both extensions into the end brackets using the two (308171. 022) 3/16 x 3/8" pop rivets. Unwind ONLY ONE wrap of the awning to allow easy insertion into the awning rail. Slide wall brackets onto each hex extension. WARNING Severe injuries can result from a spinning bracket. Do Not remove cotter pins until instructed to do so by these instructions. INSTALL AWNING RAIL 1. See figure 2, 3, 4 and 9 to determine the correct location for the awning rail. Apply a sealant to the back edge of the awning rail to prevent leaks, and install the awning rail using the (3107216. 008) #6 x 1/2" screws or equivalent. The rail must be FIRMLY mounted to the vehicle. Remove any drip shields or flashing which conflict with the awning. The awning can be assembled and held in location to check for conflicts with flashing. 6 Measure From Bottom Of Awning Rail Mounting Distance Measure From Inside Edge Of Slide-Out Room Frame. MOUNTING DISTANCE MNTG BRKT 3106992. X21X 6" - 7" MNTG BRKT 3106992. X39X 6" - 7" MNTG BRKT 3106992. X47X 4" - 5" MNTG BRKT 3106992. X70X 6" - 7" MNTG BRKT 3106992. X88X 4" - 5" MNTG BRKT 3106992. X96X 6" - 7" Slide Topper Installation & Operating Instructions FIG. [. . . ] Note: Not all installations will be able to use a Dometic edge protector. If a Dometic edge protector is not used, a similar type MUST be used. Units which are damaged by the slideout-room will NOT be covered under warranty. Note: Oscar rivets and edge protectors are available as separate items. [. . . ]