User manual DRAPER CORDLESS DRILLS

[. . . ] 19 6. 1 Create a private encrypted network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6. 2 Add an extra Homeplug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6. 3 Remove a device from a network Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6. 4 Make two public network devices private . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Never set up the Homeplug adapter near a heater or radiator. The Homeplug adapter should be located only where sufficient ventilation according to the instructions of the manufacturer can be ensured. Disconnect the Homeplug adapter from the power supply grid before cleaning. Never use water, paint thinner, benzene, alcohol or other strong cleaning agents when cleaning the device, as these could damage the case. Never use the Homeplug adapter with a power supply that does not meet the specifications provided on the rating plate. If you do not know what type of power supply you have at home, contact your dealer or energy supplier. In the event of damage, disconnect the Homeplug adapter from the power supply grid and contact customer service. This applies, for example o if the power cable or plug is damaged o liquid has been spilled on the Homeplug adapter or objects have fallen into the device. o the Homeplug adapter has been exposed to rain or water. o the Homeplug adapter does not work, even though the operating instructions have been followed properly. o the Homeplug adapter’s case is damaged. • • Full manual Sitecom Homeplug 4 2 Introduction In this chapter, we will provide an overview of the Homeplug technology and introduce it briefly. 2. 1 What exactly is Homeplug? Homeplug is home and office networking using the electric wiring already installed in the building. Cost factor and transmission quality Homeplug is an economical and easy-to-use networking technology. Press 10 seconds: clear the current network group name and randomly generate a new network group name. Press 2 to 3 seconds: this will enter Group pairing mode. In this mode the device GROUP Button will join into an existing logical network of other device or announce its network group name for other devices to join. This mode automatically ends after two minutes or when it is successful, manually stopped. Press this button 2 to 3 seconds will manually stop the Group pairing mode. Full manual Sitecom Homeplug 7 4. Install the hardware Note: If you use this manual to add a single Homeplug to an already existing Homeplug network, please follow the steps as described in Appendix A. 4. 1 Install the Master Homeplug Start with the Homeplug which is labeled as ‘Master’. You’ll see this on the backside of the Homeplug. Plug the Ethernet cable in the Ethernet port on the master Homeplug. Connect the master Homeplug to your computer and plug it into the socket. Full manual Sitecom Homeplug 8 4. 2 Install the Slave Homeplug Take the Homeplug which is labeled as ‘Slave’. You’ll see this on the backside of the Homeplug. Plug the Ethernet cable in the Ethernet port on the slave Homeplug. Connect the slave Homeplug to your Internet router and plug it into the socket. Full manual Sitecom Homeplug 9 Your network is now fully functional. Follow the next steps to secure your network. Full manual Sitecom Homeplug 10 4. 3 Install the software Note: If you use this manual to add a single Homeplug to an already existing Homeplug network, please follow the steps as described in Appendix A. Install the software only on the PC which is connected to the Master Homeplug. Insert the CD in the computer. Windows 7/Vista will prompt you to run CDMenu4. exe. The CD menu will start. [. . . ] This device can then ask other devices to join its Homeplug network to form a private network group. Any other device, the Slave Homeplug for instance, which wants to join this device’s (the Master) Homeplug network group can be added by the steps below: (NOTE: it is more convenient to bring devices, which are to be configured into the same logical network group, side by side during this procedure. After the network group is set, the devices can be deployed anywhere at home) Full manual Sitecom Homeplug 19 6. 1 Create a private encrypted network Step 1. (Clear group attribute) First clear the original network group of the Master HomePlug by pressing its GROUP button more than 10 seconds until all LED lights simultaneously turn off and on once. [. . . ]