User manual DSC ALEXOR PC9155

[. . . ] 2-Way Wireless Security Suite User Manual N11427 IMPORTANT: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The keypad will display the user number (e. g. , 01) with a letter "P" if a user code has already been programmed and a letter "T" if a code and prox tag have been programmed. NOTE: User 40 for the master code cannot be deleted; an attempt to delete this user code will delete the prox tag only. The prox tag must be re-enrolled before it can be used again. Proximity Tag Operation Place the prox tag near the tag reader ( ) at the left side of the display to arm/disarm your system. When arming the system, the following message will be displayed: Exit Delay in Progress When disarming the system, the following message will be displayed: System Disarmed If there is an attempt to swipe a prox tag that has not been enrolled, an error tone will sound and the following message will be displayed: Invalid Tag Return to Step1 for instructions on how to enroll the prox tag. WARNING: KEEP THE PROXIMITY TAG OUT OF REACH OF SMALL CHILDREN. THE MATERIALS ASSOCIATED WITH THIS PRODUCT (LITHIUM BATTERIES, ETC. ) MUST BE RECYCLED ACCORDING TO LOCAL RULES AND REGULATIONS. 8 User Function Commands Disarm the system then enter , [Master Code]. The , command is used to gain access to the following list of Master functions of the system: [1] Time and Date - Enter 4 digits for 24hr System Time (HH-MM). Valid entries are 00-23 for the hour and 00-59 for minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY). [4] System Test - The system's Siren Output - 4 seconds (2 seconds medium volume, 2 seconds high volume), keypad lights, back-up battery pack and communicator are tested. [5] Enable DLS / Allow Remote System Service - If enabled, the installer will be able to access Installer Programming remotely using DLS (Downloading Software). This function provides a window for telephone ring detection by the alarm system. The DLS window will remain open for 6 hours, during which time the installer will be able to enter DLS an unlimited number of times. After the 6-hr window has expired, access to programming via DLS will be unavailable until the window is re-opened. [6] User Call-up - If enabled by the installer, the panel will make 1 attempt to call the downloading computer. The downloading computer must be waiting for the panel to call before downloading can be performed. [8] User Walk Test - Allows the user to enter the Walk Test mode. [9] Late to Open Enable/Disable - This function enables or disables the Late to Open time programmed in [0]. [0] Late to Open Time of Day - This function is used to program the time setting enabled in [9]. NOTE: Refer to `Late to Open' section for details. Changing Brightness/Contrast When this option is selected, the keypad will allow you to scroll through 4 brightness levels and 10 contrast levels. Use the buttons to scroll to either Brightness Control or Contrast Control. Press , to select the setting you want to adjust. [. . . ] It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected. Access by Intruders Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system. Power Failure Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. [. . . ]