User manual DSC PC3000

[. . . ] System Reference Zone 1 2 3 4 5 6 7 8 Area ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ Type _____________ _____________ _____________ _____________ _____________ _____________ _____________ _____________ Fire Zone: ___________________________________________________________ Keypad Zones Keypad Zone [F] Fire _________________________________________________ Keypad Zone [A] Auxiliary _____________________________________________ Keypad Zone [P] Panic _______________________________________________ Access Codes Access Code 1 2 3 4 5 6 7 8 ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ Assigned To. . . _____________ _____________ _____________ _____________ _____________ _____________ _____________ _____________ 9 10 11 12 13 14 15 16 Access Code ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ Assigned To. . . _____________ _____________ _____________ _____________ _____________ _____________ _____________ _____________ Entrance and Exit Delays Entry Delay: Exit Delay: seconds seconds Auxiliary Entry Delay: Auxiliary Exit Delay: seconds seconds Monitoring Station Account Number: __________________________ Phone: ____________________________________ For Service Call: ______________________________________ Phone: ____________________________________ A Word About Your System The PC3000 Security System has been designed to give you the greatest possible flexibility and convenience. Read this manual carefully and become familiar with the operation of your Security System. Your installer will tell you which commands listed in this manual apply to your system. Fill out the System Reference sheet in this manual and store it in a safe place for future reference. [. . . ] Ready light flashing with "Armed" light ON indicates access code 9-16 programming. Bypass light comes ON when you bypass a zone. To bypass a zone, press [ ], [1], [Master Code] and then the zone(s) you wish to Bypass. Enter 01 for zone 1; 08 for zone 8; 16 for zone 16. Press [#] to return to ready. When ON in the normal operating mode, the Zone Lights indicate an open zone. Refer to zone chart on keypad door for zone information. Armed light will come ON indicating system is armed. Ensure "Ready" light is ON, enter [4 digit] access code. Armed light flashing with "Ready" light indicates access code 9-16 programming. * Trouble light ON means there is a fault on the system. Press any key to silence keypad beeping. Press [ ] then [2] to display trouble type; one or more zone lights will come ON to indicate the type of trouble. Memory light ON means an alarm has occurred. To display zone that caused alarm, press [ ] then [3]. Zone light will come on indicating which zone caused the alarm. * * 1 2 3 4 5 6 7 8 Battery A. C. They are activated by pressing two keys at the same time and holding them for 2 seconds. These zones may or may not be active on your keypads depending on how your installer has programmed them. [F] Keypad FIRE zone. Pressing this key for 2 seconds will activate the keypad fire zone and the bell/siren output will pulse ON and OFF. This zone is annunciated by the "Fire" light on the keypad. Pressing this key for 2 seconds will produce a series of beeps on the keypad along with the transmission. To confirm transmission, the keypad sounder will beep 6 times. Depending on how your installer programs the panel, pressing this key for 2 seconds may produce a completely silent alarm or an audible alarm along with the transmission. If programmed as audible, the alarm bell will ring. [A] [P] Testing It is recommended that the system be tested on a weekly basis. NOTE: Perform tests in the off-peak hours, such as early morning or late evening. 1 Inform the monitoring station that you are testing your system. 2 Disarm the system ("Ready" light should be ON). [. . . ] The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. [. . . ]