User manual DSC PC560

[. . . ] TABLE OF CONTENTS SYSTEM INFORMATION INTRODUCTION 2 3 Test Your System Regularly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BASIC OPERATION 4 Arming Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When a condition occurs that could affect operation, the "System" light will come ON and the keypad will sound two short beeps every 10 seconds to warn of the trouble condition. To silence the sounder, press the [#] Key. The keypad will be silenced, but the "System" light will remain ON until the trouble condition is cleared. To display the trouble conditions, enter [ ][2]. Trouble conditions are represented with the Zone Lights; if a Zone Light comes ON, then that trouble condition is present: Zone Light Trouble Cause What To Do 1 2 Battery Trouble AC Failure Battery is low or disconnected AC power is out Call for service Check your fusebox or circuit breakers; call for service if the trouble condition cannot be corrected Call for service if trouble does not correct itself 4 Communications Trouble System cannot communicate with monitoring station Note that the keypad sounder will not beep if only the AC Failure trouble is present. 9 CHANGING SYSTEM FEATURES Changing Access Codes The PC560 features 4 programmable Access Codes. The first code is the Master Code, and the remaining three codes are normal Access Codes. Programming Access Codes: Enter [ ][5][Master Code]; the "Ready", "Armed" and "System" lights will FLASH. The Zone Lights will indicate which Access Codes have been programmed, and which Access Code is presently being programmed: Zone Light Access Code is. . . When the [ ][5][Master Code] command is entered, Zone Light 1 will be ON to indicate that the Master Code is already programmed. OFF ON steady Flashing not programmed programmed presently being programmed Changing or Adding a Code: To change the Master Code or Access Codes 2 through 4, enter the number of the code to be changed; the corresponding Zone Light will begin to FLASH. For example, enter [1] to change the Master Code, or enter [2] to change Access Code 2, and so on. With the desired Zone Light flashing, enter a new 4-digit Access Code. Do not press [ ] or [#] when entering the code. If an existing code is being changed, the new code will replace the old one. After the code is entered, the keypad will beep 3 times and the Zone Light will stop flashing and remain ON. If you want to program another code, press the number key for the code to be programmed, and enter the new 4-digit code as described above. When all desired changes are complete, press the [#] Key to return to "Ready". Erasing a Code: To erase a code, enter [ ][5][Master Code]. Enter the number of the code to be erased; the Zone Light for the code will FLASH. When all desired changes are complete, press the [#] Key to return to "Ready". IMPORTANT: Do not erase the Master Code. If the Master Code is accidentally erased, contact your installing company for assistance. Door Chime On/Off The Door Chime feature causes the keypad to beep whenever an Entry-Exit Zone or Instant Zone is activated. This feature is useful if the Entry-Exit door or doors are out of view, and you would like an indication of when the door zones are opened and closed. Note that the Door Chime feature only functions when the system is disarmed. To turn the Door Chime feature ON or OFF, enter [ ][6]. If the feature is being turned ON, the keypad sounder will beep 3 times. If the feature is being turned OFF, the sounder will emit a single long tone. Adjusting the Keypad Sounder Tone and Backlighting The sounder tone and the lighting behind the keys for each Keypad may be individually adjusted. The sounder tone may be set with a loud tone, a softer tone, or no tone at all. The backlighting can be set at medium or high brightness, or it may be turned off. To adjust the Keypad's sounder, press and hold the [#] Key; after two seconds, the sounder will begin to beep. With each beep, the tone of the beep will increase or decrease. [. . . ] Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. s Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. [. . . ]