User manual DSE G7659

[. . . ] Deep Sea Electronics Plc reserves the right to change the contents of this document without prior notice. 2 057-012 G7659 OPERATING MANUAL ISSUE 5. 1 18/06/2007 AM DSE Model G7659 Automatic Mains Failure & Instrumentation System Operators Manual TABLE OF CONTENTS Section 1 2 3 Page INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION. 5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 1 3. 2 3. 3 AUTOMATIC MODE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] DSE have produced the `insert card creator' software, shipped with the DSE Software CD to ease the production of text and logo insert cards to suit your application. Removal and insertion of the text insert card Removal and insertion of the Logo insert card 16 057-012 G7659 OPERATING MANUAL ISSUE 5. 1 18/06/2007 AM DSE Model G7659 Automatic Mains Failure & Instrumentation System Operators Manual 6 DESCRIPTION OF CONTROLS The following section details the function and meaning of the various controls on the module. Scroll Configure / log Stop Manual Test Auto Start FIG2 G7659 OPERATING MANUAL ISSUE 5. 1 18-Jun-07 AM 17 DSE Model G7659 Automatic Mains Failure & Instrumentation System Operators Manual 6. 1 TYPICAL LCD DISPLAY SCREENS The LCD displays the various engine parameters such as `ENGINE SPEED', `OIL PRESSURE', `HOURS RUN', etc. Each instrument is displayed with the appropriate units of measure. In this example, the values being displayed are Generator phase to neutral L1-N, AC voltages V. INSTRUMENTS STATUS ICONS The LCD also displays the status of the controller by showing (for example) an hourglass symbol when a timer is in progress or by displaying a common alarm symbol. This display is indicating that a timer is in progress and a warning alarm is present. See the `Protections' section of this manual for details of the alarms. In this example the values being displayed are the three generator USER DEFINED INDICATIONS AC currents A The LCD displays the user-defined indications when configured and active. The icons will illuminate and point to the appropriate text insert label. These indications can be used to indicate the operation of external equipment (i. e. `Battery Charger On', `Breaker Closed' etc) or to indicate internal states (i. e. Engine Running, Safety On, etc). USER DEFINED ALARMS The LCD displays the user-defined alarms when configured and active. The icons will illuminate and point to the appropriate text insert label. will cycle through the past alarms until all 15 logged alarms have been viewed, Continuing to press down after which the most recent alarm will again be showed and the cycle will begin again. To exit the event log and return to viewing the instruments, press the log button. G7659 OPERATING MANUAL ISSUE 5. 1 18-Jun-07 AM 21 DSE Model G7659 Automatic Mains Failure & Instrumentation System Operators Manual 6. 5 INDICATORS COMMON ALARM LCD indicators These indicate when an alarm condition is present. The Alarm icons or LEDs will detail the exact nature of the alarm. USER CONFIGURABLE LCD INDICATORS These LCD's can be configured by the user to indicate any on of the different functions based around the following:· INDICATIONS - Monitoring of a digital input and indicating associated functioning user's equipment - Such as Battery Charger On or Louvres Open, etc. · WARNINGS and SHUTDOWNS - Specific indication of a particular warning or shutdown condition, backed up by LCD indication (!)Such as Low Oil Pressure Shutdown, Low Coolant level, etc. · STATUS INDICATIONS - Indication of specific functions or sequences derived from the modules operating state - Such as Safety On, Pre-heating, Generator Available, etc. (warning) or (shutdown) 6. 6 CONTROLS STOP/RESET This button places the module into its Stop/reset mode. This will clear any alarm conditions for which the triggering criteria have been removed. If the engine is running and this position is selected, the module will automatically instruct the changeover device to un-load the generator (`Load transfer' becomes inactive (if used)). The fuel supply will be removed and engine will be brought to a standstill. Should a remote start signal be present while operating in this mode, a remote start will not occur. MANUAL This mode is used to allow manual control of the generator functions. [. . . ] The 5210 module may be used in conjunction with DSE Automatic transfer switch controllers such as the model 500 (pictured) , 705 or 530. These not only monitor the mains and issue a start command to the 5210; they also provide control of the contactors or other changeover devices. Please refer to our Technical Support department for details. 50 057-012 G7659 OPERATING MANUAL ISSUE 5. 1 18/06/2007 AM DSE Model G7659 Automatic Mains Failure & Instrumentation System Operators Manual 15. 9 ENCLOSURE CLASSIFICATIONS IP CLASSIFICATIONS BS EN 60529 Degrees of protection provided by enclosures First Digit Protection against contact and ingress of solid objects 0 1 No protection Protected against ingress solid objects with a diameter of more than 50 mm. No protection against deliberate access, e. g. [. . . ]