User manual DUAL XD6320

[. . . ] The XD6320 uses one 10 amp ATM fuse located beside the wiring connector. 3 XD6320 OPERATION Control Locations 1 2 3 4 5 6 7 8 9 10 22 21 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 11 Release Power Volume Band/Play/Pause Mode Auto Store/Preset Scan Tune/Track Down Eject Tune/Track Up Display EQ 12 13 14 15 16 17 18 19 20 21 Tuner Scan Local/Distance Preset 6 Preset 5 Preset 4 Preset 3/Intro Preset 2/Random Preset 1/Repeat Audio Loudness 22 Mute 4 XD6320 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32" Phillips head screw through left side of mounting frame into faceplate. Press POWER or any other button (except eject) to turn the unit on. [. . . ] Press and hold AUDIO for 3 seconds to turn confirmation beep on/off. "MUTE" will flash in the display. Press MUTE again to cancel. Reset Confirmation Beep Mute 6 XD6320 OPERATION General Operation Audio Press AUDIO to select between Volume (default), Bass, Treble, Balance & Fader. Bass Press AUDIO until BAS appears Rotate encoder left/right to adjust ( -6 minimum / +6 maximum) Press AUDIO until TRE appears Rotate encoder left/right to adjust ( -6 minimum / +6 maximum) Press AUDIO until BAL appears Rotate encoder left/right to adjust (BAL L 12-BAL 00-BAL R 12) BAL 00 represents equal balance Press AUDIO until FAD appears Rotate encoder left/right to adjust (FAD F 12-FAD 00-FAD R 12) FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM, FM, CD, and AUX modes. This allows you to save the Bass and Treble settings separately for each mode. Example: FM tuner mode can have Bass +3 and Treble -1 while CD mode can have Bass +2 and Treble +2. Note: Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Treble Balance Fader Source Audio Memory 7 XD6320 OPERATION Tuner Operation Seek Tuning Press TUNE or TUNE next strong station. nn nn ll momentarily to seek the ll Manual Tuning Press TUNE or TUNE for more than 2 seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. nn ll Scan Tuning Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press LOC to activate local tuning for strong station reception only. Press LOC again to cancel and resume distance tuning (default). Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Press and hold BAND then press TUNE to select European frequency spacing. Press and hold BAND then press TUNE to select USA frequency spacing (default). Local/Distance Band Frequency Spacing nn ll Storing and Recalling Station Presets Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. [. . . ] Before you call for service, check your operating instruction booklet. A slight adjustment of any custom controls discussed in your instruction booklet may save you a service call. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with proof of the purchase date from the retailer to the Return Center address listed below. Please describe your problem in writing and include your name, a return UPS shipping address (P. O. [. . . ]