User manual DURACRAFT DCM200

[. . . ] If it still does not fit, contact a qualified electrician. DO NOT attempt too defeat this safety feature. To disconnect the humidifier, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. [. . . ] If it has to be moved, unplug the humidifier and remove the water tank first. NOTE: DO NOT POUR WATER INTO THE GRILL ON THE TOP OF THE MOTOR HOUSING. DOING SO MAY DAMAGE THE HUMIDIFIER OR CAUSE PERSONAL INJURY. O P E R AT I O N CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH WET HANDS AS AN ELECTRIC SHOCK COULD OCCUR. POWER · With the power switch in the OFF position, plug the filled humidifier into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way. HUMIDITY CONTROL 1. Set the fan speed control to the desired position (Fig. HIGH: For fast humidifying LOW: For quieter operation Fig. 4 f Of High Lo w NOTE: The length of time your humidifier runs will vary depending on the quality of construction and insulation of your room and house, as well as the fan speed. Turn the humidifier OFF if the humidity level feels too moist or you notice condensation forming on the walls and/or windows. ALWAYS be sure to empty any unused water in the Rinse-to-Clean® Base and/or Water Tank each time you refill the water tank or finish using the humidifier. W E E K LY C L E A N I N G We recommend cleaning the humidifier once a week, more often if you have hard water or notice a build up of impurities or detect unpleasant odors. NOTE: THE USE OF OTHER WATER TREATMENT PRODUCTS MAY DAMAGE THE FILTER OR HUMIDIFIER. Cleaning involves two steps SCALE REMOVAL and DISINFECTING. Be sure to perform these in the proper order to avoid harmful chemical interactions. · First, turn off and unplug the humidifier. · Remove the Water Tank and Motor Housing. · Remove the Natural Cool Moisture® filter from the Rinse-to-Clean® Base. · Discard any residual water from the Base. · Clean all outside surfaces with a dry, soft cloth. THIS MAY DAMAGE THE HUMIDIFIER OR CAUSE ELECTRIC SHOCK. NOTE: Remove filter before cleaning Failure to remove the filter during cleaning will destroy the filter STEP ONE: STEP TWO: SCALE REMOVAL Rinse-to-Clean® Base 1. Fill the Rinse-to-Clean® Base with either: · one cup (8 ozs) of undiluted white vinegar OR · DuraRinse Humidifier Cleaner, part no. AC-816, following bottle instructions ® DISINFECTING Water Tank 1. Fill the water tank with: · 1 teaspoon of household bleach · 1 gallon of water. Pour some of this solution into the Rinse-to-Clean® Base. Rinse with water until the odor of bleach is gone. 2. With the vinegar or DuraRinse® in the Rinse-to-Clean® Base clean all interior surfaces with a soft cloth or brush to help remove scales. Rinse the Rinse-to-Clean® Base thoroughly with water to remove scale and cleaning solution. P R O L O N G I N G T H E L I F E O F T H E F I LT E R A N D M A I N TA I N I N G A C L E A N H U M I D I F I E R NOTE: DO not attempt to clean the Natural Cool Moisture® filter with any chemical solutions, doing so will damage the filter. · If the Natural Cool Moisture® filter appears to be clogged by hard water or mineral deposits, soak it in a sink full of cool water for 10 minutes. [. . . ] Soak filter in a sink full of cool water to help break up deposits. The discoloration may remain but will not effect the humidifier's performance. E L E C T R I C A L R AT I N G S This product is rated at 0. 6 amps, 120V, 60 Hz. NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HUMIDIFIER PLEASE SEE THE WARRANTY INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HUMIDIFIER YOURSELF. DOING SO WILL VOID THE WARRANTY AND COULD CAUSE DAMAGE TO THE UNIT OR PERSONAL INJURY. [. . . ]