User manual DURKOPP DAC CLASSIC CLASS 271 MANUAL PART II V 12-2010

[. . . ] Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. [. . . ] 0 = off; 1 = on Mode for the end of the start backtack. 0 = You sew further after the end; 1 = Machine stops and must be started by the pedal again; 2 = Thread performance after the start backtack Pedal release only to an additional route A 0 = off; 1 = on Delay time up to the speed release after the start backtack End backtack speed Pre-control angle when switchin g on the backtack magnet. (Switchover of forward backward at the bartack) Pre-control angle when turning the backtack magnet off. (Changing of backward forward at the bartack) Backtack magnet stays switched on (simple with the last backward way final backtack and multiple backtack ends) till the needle has been reached the Pos. 0 = off; 1 = on Start multiple backtack speed (only at the stuffing program) Pre-control angle when switchin g on the backtack magnet. (Switchover of forward backward at the backtack) (only at the stuffing program) Pre-control angle when turning the backtack magnet off. (Change of backward forward at the backtack) (only at the stuffing program) Start backtack as a stuffing program. 0 = off; 1 = on Ornamental backtack 0 = off; 1 = on Ornamental backtack speed Stop time at the ornamental backtack and the reset button at the same t 00 04 0 2 0 - t 00 05 0 1 1 - t t t t t 00 00 00 00 00 06 10 11 12 13 0 300 0 0 0 500 2500 254 254 1 0 1700 12 17 0 ms rpm 10° 10° - t t 00 00 20 21 300 0 4000 254 2800 22 rpm 10° t 00 22 0 254 24 10° t 00 23 0 1 0 - t 00 30 0 1 0 - t t 00 00 31 32 0 0 2500 1000 1200 200 rpm ms © 2010 Dürkopp Adler AG II-5 Operating manual part II L t C 00 P 35 Min 0 Max 1 Preset 1 Unity - t t 00 00 36 40 0 0 2000 2 500 1 rpm - t 00 41 0 2 1 - t 00 45 0 1 0 - t 00 46 0 1 0 - t t t 00 00 00 50 51 52 0 5 0, 0 999 100 600, 0 100 100 60, 0 ms % s t t 00 00 53 54 5 0 90 1 45 1 % - Description Reducing speed when shifting the feed dog 0 = off; 1 = on Wished speed reduction when shifting the feed dog. Type of the start backtack, if the backtacking is toggled. 0 = Simple start backtack; 1 = Double start backtack; 2 = Start multiple backtack Type of the end backtack, if the backtacking is toggled. [. . . ] 0 = No; 1 = Yes Number of stitches till lower the roller Showing software version Showing control serial number Showing machine serial number Showing production date Showing machine class and ­sub class Load of parameters 0 = Nothing; 1 = Sewing data of the there dongle; 2 = Sewing data of the backup area; 3 = Seam ways of the there Dongle 4 = Master reset Store of parameters 0 = Nothing; 1 = Sewing data on the there dongle; 2 = Sewing data to the backup area; 3 = Seam ways on the there Dongle t 12 01 10 t 12 02 10 Needle cooling t 13 00 0 180 255 1 10 20 0 ° ms - t 13 t 13 Roller t 14 01 02 00 0, 0 100 0 9, 999 9999 3 2, 500 !!!!0 s rpm - t 14 01 0 1 0 - t 14 02 0 1 0 - t 14 03 0 255 Miscellaneous of the control t 51 00 t 51 01 t 51 02 t 51 03 t 51 04 t 51 10 0 4 0 - Stitches - t 51 11 0 3 - - II-12 © 2010 Dürkopp Adler AG Operating manual part II L t C 51 P 12 Min - Max - Preset - Unity - t t 51 51 13 14 0 1 - - Description Hardware-Test Bold Inputs or Outputs are only available at DACclassic controls. [. . . ]