User manual DYNACORD EX24

[. . . ] Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or orbjects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment. To completely disconnect this equipment from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable. [. . . ] Any work security regulations that are applicable at the locations where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations about the work place itself. The Wheelie Bin symbol found on the product or in the manual indicates that this product must not be disposed of with other waste. It is in our category the manufacturer's responsibility to properly dispose of their waste electrical and electronic equipment (WEEE) at the end of its life. Due to the differences in each EU country's management of WEEE, please contact your local distributor. We are committed to facilitate our own electronic-waste-management-system, for the free of charge return of all EVI Audio GmbH products: Telex, DYNACORD, Electro-Voice and RTS. Arrangements are made with the dealer where you purchased the equipment from, for the returning of all unusable equipment at no cost, to the factory in Straubing, for environmental protective disposal. The DYNACORD PowerSub 112 and 212 powered subwoofers are perfectly suited for building multi-component active loudspeaker systems, e. Due to its vented design this subwoofers offers much more musical, tight and punchy bass than typical bandpass designs often found in this type of product range. PowerSub 112 The PowerSub 112 is great for enhancing the low frequency response of active fullrange speakers like the D 8A. Despite its light weight and compact dimensions the subwoofer still produces a very powerful bass line even at very low frequencies. Operation of this equipment in a residental area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. PS 112 Power on/off indicator (POWER) Mains switch (ON / OFF) Mains connector, lockable (MAINS IN) Limit indicator (LIMIT) Volume control (VOLUME) Polarity indicator (180°) Polarity switch (PHASE) Output connector (XLR) for mid/hi audio signal (MID/HIGH OUT) Input connector (XLR or phone) for line level audio signal (LINE IN) Output connector (XLR) for line level audio signal (LINE THRU) Output connectors (XLR) for left or right mid/hi audio signal (MID/HIGH OUT L or MID/HIGH OUT R) Input connectors (XLR or phone) for left or right line level audio signal (LINE IN LEFT or LINE IN RIGHT) Output connectors (XLR) for left or right line level audio signal (LINE THRU LEFT or LINE THRU RIGHT) The POWER LED lights after turning the power ON. If the mains cord is correctly connected, mains voltage is present and the LED does not light upon power-on, please contact your local dealer. 3 MAINS CONNECTOR (MAINS IN) The PowerSub receives its power supply via the lockable MAINS IN connector. Only the provided power cord may be used. Connect the PowerSub only to a mains network, which corresponds to the requirements indicated on the type plate. Press the yellow button at the plug to disconnect the power cord. 4 LIMIT INDICATOR (LIMIT) Brief blinking of the LIMIT LED indicates that the power amplifier of the PowerSub is operated at its limits. 7 POLARITY SWITCH (PHASE) Select 0° (button not pressed) if the signal polarity should not be inverted. The level of the output signal is independent of the setting of the level control VOLUME ("Pre Fader"). Whenever possible, balanced signal feed is always preferable to guard against potential noise or HF-interference. [. . . ] Now, have fun with your PowerSub system!After use, first switch off the D 8A, then the PowerSub and then the mixing console, so that distracting power-off noise will not occur. When using a DYNACORD CMS mixer, no power-off noise will be output from the `Master Outputs`. This allows switching off the mixer first without a problem. [. . . ]