User manual DYNATEK DDK1-7

[. . . ] Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance. € Liquid petroleum gas sinks to the floor as it is heavier than air. Therefore, rooms containing LPG cylinders must also be equipped with vents to allow gas to escape in the event of a leak. [. . . ] Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. In the event of discrete-adjustment knobs with LED visualisation, turn the knob to the minimum power setting them remove it and intervene on the adjustment screw located near the tap pin. Minimum setting adjustment of the DRDA (DCDR) burner with discrete adjustment and LED visualisation: • To adjust the outer ring, turn the knob anticlockwise to the minimum power position. € To adjust the minimum power setting of the inner ring, turn the knob clockwise to the minimum power position. € Remove the knob and intervene on the adjustment screw located near the tap pin. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). GB 24 can be enlarged by turning on both "A" and "B". To turn only the circular "A" element, simply turn the knob in the clockwise direction to any one of the 12 available settings. To add the "B" section, turn the knob to setting 12 and then click it into the setting. Then proceed by turning the knob in the counter-clockwise direction to one of the 12 settings. The figure shows the heating zones, which become red when the element is turned on. Indicator light to show when the cooking zone is above 60°C, even after the heating element has been turned off. Burner Rapid (R) Semi-Rapid (S) Auxiliary (A) Triple Crown (TC) Double Flame (DCDR internal) Double Flame (DCDR external) Ø Cookware Diameter (cm) 24 - 26 16 - 20 10 - 14 24 - 26 10 - 14 26 - 28 GB Pans to be used on 60 - 65 cm hobs Burner Reduced Rapid (RR) Semi-Rapid (S) Auxiliary (A) Semi-Fishburner (SP) Ø Cookware Diameter (cm) 24 - 26 16 - 20 10 - 14 16 - 20 24 - 26 24 - 26 10 - 14 26 - 28 B Triple Crown (TC) Ultra Rapid (UR) A Double Flame (DCDR internal) Oval R ing C Double Flame (DCDR external) Pans to be used on 75 cm hobs When the knob is on any of the settings other than "Off", the Indicator Light for Ceramic Glass Module comes on. Practical advice on using the burners To ensure the burners operate efficiently: • Use appropriate cookware for each burner (see table) so that the flames do not extend beyond the bottom of the cookware. € Always use cookware with a flat base and a cover. € When the contents of the pan reach boiling point, turn the knob to minimum. On the models supplied with a reducer shelf, remember that this should be used only for the Double flame internal (DCDR internal) burner when you use casserole dishes with a diameter under 12 cm. [. . . ] € Before using the ceramic glass module, the surface must be cleaned, using a damp cloth to remove dust or food residues. The ceramic glass surface should be cleaned regularly with a soultion of warm water and a nonabrasive detergent. Periodically, special products will need to be used to clean the surface. First, remove all food buildup or grease with a cleaning scraper, e. [. . . ]