User manual DYNATEK DDK3-6

[. . . ] Pass them on to possible new owners of the appliance. Also be equipped with vents to allow gas to escape in the event of a leak. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc. It is advisable to keep only the cylinder being used in the room, positioned so that it is not subject to heat produced by external sources (ovens, fireplaces, stoves, etc. [. . . ] The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with 14 These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Remove the hob grids and slide the burners off their seats. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. 78 MJ/m3 RR UR A PZ PZ PZ PZ PZ PZ 750/HA 750 GH/HA 750 N/HA 750 GH N/HA 750 K/HA 750 GH K/HA S S PZ PZ PZ PZ PZ PZ RR A DCDR S S 750 R/HA 750 R GH/HA 750 R N/HA 750 R GH N/HA 750 RK/HA 750 R GH K/HA 16 Description of the appliance Overall view GAS BURNERS GB Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES* Ignition for GAS BURNERS* • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. € Control Knobs for GAS BURNERS adjust the power or the size of the flame. • GAS BURNER ignition* enables a specific burner to be lit automatically. € SAFETY DEVICE* stops the gas flow if the flame is accidentally extinguished. The lateral hob grids may be inverted by positioning the RH-side grid on the LH-side and vice-versa. If this happens, the misalignment of the spokes will be evident and they will no longer intersect at the centre of the burner (see picture). The position of the corresponding gas burner is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: • Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. To light a burner, simply press the corresponding knob all the way in and then turn it in the counterclockwise direction to the "High" setting, keeping it pressed in until the burner lights. [. . . ] This procedure must be performed by a qualified technician authorised by the manufacturer. Do not use abrasive or corrosive detergents such as stain removers, anti-rust products, powder detergents or sponges with abrasive surfaces: these may scratch the surface beyond repair. Never use steam cleaners or pressure cleaners on the appliance. € It is usually enough to wash the hob with a damp sponge and dry it with absorbent kitchen roll. [. . . ]