User manual DYNATEK DS2-1

[. . . ] Safety Device (only on certain models) - Activates if the flame accidentally goes out (spills, drafts, etc. ), interrupting the delivery of gas to the burner. C E How To Use Your Appliance The position of the corresponding gas burner or electric hot plate (if present) is indicated on each control knob. Gas Burners The burners differ in size and power. Choose the most appropriate one for the diameter of the cookware being used. The burner can be regulated with the corresonding control knob by using one of the following settings: ? [. . . ] The following should be avoided: - Touching the appliance with wet parts of the body; - Using the appliance with bare feet; - Pulling on the appliance or the power supply cord to disconnect them from the electrical outlet; - Improper and/or dangerous use; - Obstructing the ventilation or heat dissipation slots; - Allowing the power supply cord of small appliances to come into contact with the hot parts of the cooktop; 4 The assistance of qualified personnel must be called upon in the following cases: - Installation (in accordance with the manufacturer's instructions); - When in doubt about the operation of the appliance; - Replacement of the electrical outlet becuase it is incompatible with the plug. Contact service centers authorized by the manufacturer in the following cases: - When in doubt about the condition of the appliance after having removed the packing; - Damage to or replacement of the power supply cord; - In the case of a breakdown or malfunction: ask for original spare parts. It is recommended that you follow the guidelines below: - Only use the appliance to cook food, avoiding all other uses; - - Check the condition of the appliance after it has been unpacked; Disconnect the appliance from the power supply in the event of malfunction and always before cleaning or maintenance; When not in use, disconnect the appliance from the power supply and turn off the gas valve (if present); - ? Always check to make sure that the control knobs are on the ???/?o?setting when the appliance is not in use; Cut the power supply cord after disconnecting it from the electrical mains when you decide to no longer use the appliance. The manufacturer will not be held liable for any damages arising out of : incorrect installation or improper, incorrect or unreasonable use. . Installation Instructions for built-in The following instructions are intended for the installer so that the installation and maintenance procedures may be followed in the most professional and expert manner possible. Important: Disconnect the appliance from the electrical supply before performing any maintenance or regulation upkeep work. Positioning the Cooktop Important: this unit may be installed and used only in permanently ventilated rooms in accordance with British Standard Codes Of Practice: B. S. The following requirements must be observed: a) The room must be fitted with a ventilation system which vents smoke and gases from combustion to the outside. This must be done by means of a hood or electric ventilator that turns on automatically each time the hood is operated. Detail A Adjacent Room Room to be Vented A Examples of ventilation holes for comburant air. Enlarging the ventilation slot between window and floor. Fig. B c) Intensive and prolonged use of the appliance may necessitate supplemental ventilation, e. g. opening a window or increasing the power of the air intake system (if present). During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas tanks must be carried out according to the safety standards currently in force, and only after it is ascertained that it is suitable for the type of gas to be used. If not, follow the instructions indicated in the section entitled, ?Adapting the Cooktop for Different Types of Gas?. In the latter case, a single pole switch must be placed between the appliance and the mains, with a minimum opening between the contacts of 3 mm in compliance with current safety codes (the earthing wire must not be interrupted by the switch). The power supply cord must be positioned so that it does not reach a temperature in excess of 50C above room temperature at any point. Before making the actual connection, make sure that: ?The fuse and electrical system can withstand the load required by the appliance; ?That the electrical supply system is equiped with an efficient earth hook-up according to the norms and regulations prescribed by law; ?That the plug or switch is easily accessible. Important: the wires in the mains lead are coloured in accordance with the following code: Green & Yellow - Earth Blue - Neutral Brown - Live As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect the Green & Yellow wire to the terminal marked or coloured Green or Green & Yellow. or Connect the Brown wire to the terminal marked ?L? [. . . ] (, ). 9 - . , : , , , ; , ; , , , ; , ( ). : , . : ( ) , - . . K ()(R) (RR) (S) () () () 24 26 22 24 16 20 10 14 24 26 . 10 , . [. . . ]