User manual DYNATEK DYNAS TSG

[. . . ] This appliance is intended to be used in household and similar applications such as: - staff kitchen areas in shops, offices and other working environments; - farm houses; - by clients in hotels, motels and other residential type environments; - bed and breakfast type environments. Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. [. . . ] When the set time has elapsed, a long beep sounds, the DELAYED START indicator light switches off and the wash cycle begins. To deselect the DELAYED START option, press the DELAYED START button repeatedly until the text OFF appears. The Delayed Start function cannot be set once the wash has been started. table of options Auto Super wash Auto Normal Daily A 60 Soak Eco Speed 25’ Crystal Baby wash A Delayed Start Yes Yes Yes Yes Yes Yes Yes Yes B Half Load Yes Yes Yes Yes Yes No Yes No C Tabs Yes Yes Yes No Yes Yes Yes No D Good Night No Yes No No Yes No No No * Only available in selected models. 7 Wash cycles EN For available OPTIONS please refer to the Table of options on the Start-up and use page. If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly. The number and type of wash cycles and options may vary depending on the dishwasher model. Pre-wash for dishes while awaiting completion of the load with the dishes from the next meal. Environmentally-friendly wash cycle with low energy consumption levels, suitable for pans and dishes. Economic and fast wash to be used for lightly soiled dishes. (Run cycle immediately after use) (2 plates + 2 glasses + 4 pieces of cutlery + 1 saucepan + 1 small frying pan). Even if using multi-functional tablets, the salt dispenser should still be filled. EN Water Hardness Table Level 1 2 3 4 °dH 0-6 6 - 11 12 - 17 17 - 34 °fH 0 - 10 11 - 20 21 - 30 31 - 60 mmol/l 0-1 1, 1 - 2 2, 1 - 3 3, 1 - 6 Average salt container capacity duration** months 7 months 5 months 3 months 2 months Measuring out the rinse aid 5* 34 - 50 61 - 90 6, 1 - 9 2/3 weeks For values between 0°f and 10°f, we do not recommend the use of salt. * this setting may cause a slight increase in the duration of the cycles. (°dH = hardness measured in German degrees - °f = hardness measured in French degrees - mmol/l = millimoles per litre) Adjusting the amount of rinse aid If you are not completely satisfied with the drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster (F) to one of the 6 pre-set positions (the default position is set to 4): • If there are streaks on the crockery, set the adjustment device to a lower number (1-3). • If drops of water remain on the crockery or if there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). Setting the water hardness Every dishwasher is equipped with a water softener which, by using refined salt designed especially for this type of appliance, supplies water without limescale which is then used to wash the crockery. This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the water hardness level in your area. This information can be obtained from the organisation which supplies your household with water. The water hardness adjustment procedure may vary depending on the dishwasher model purchased. - Switch on the appliance by pressing the ON/OFF button. [. . . ] € The level of the refined salt is low or the dosage setting is not suited to the hardness of the water (see Rinse aid and salt). € The lid on the salt dispenser is not closed properly. € The rinse aid has been used up or the dosage is too low. • The rinse aid dosage is too high. [. . . ]