User manual EARLEX STEAM DYNAMO PRO

[. . . ] Instant Steamer ­ Model IS2000 USER INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE Thank you for purchasing an Earlex Instant Steam Cleaning Kit. In order to obtain the best results from this product, please read these instructions & make a special note of the Safety Rules before commencing any work. EARLEX INC. WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR ANY OTHER PURPOSES THAN THOSE DETAILED HEREIN RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE HELPLINE NUMBER - TOLL FREE 888 STEAM 12 CONTENTS Important Information Check that your Steam Dynamo Pro is complete Safety Rules Safety Precautions Steam Cleaning Delicate materials About your Earlex Steam Dynamo Pro Features Guide Preparing your Steam Dynamo Pro for use Using the main attachments Using the mini attachments Getting started Cleaning & maintenance Storing the unit Trouble Shooting Spare parts Mains connection Warranty 3 4 4 4 5 7 8 9 11 12 13 13 14 14 15 16 BEFORE PROCEEDING ANY FURTHER PLEASE CHECK THAT YOUR EARLEX STEAM DYNAMO PRO IS COMPLETE. HELPLINE NUMBER - TOLL FREE 888 STEAM 12. CALL FIRST IF YOU HAVE ANY PROBLEM 2 OPENING THE CARTON When you open the carton, you will see the Caddy unit, which has the 4 main attachments stowed inside. [. . . ] Upholstery Cleaner/Garment Steamer (29) IMPORTANT ­ Some upholstery, fabrics and soft furnishings have stain resistant treatments, which, may be affected by steam cleaning. Try cleaning a small area of material that is normally unseen, then allow 24 hours before checking whether there have been any unusual effects on the material. Check with your material supplier for further advice. Do not allow the material to become soaked. You only require a small amount of steam to clean, and soaking can leave water marks or cause bleed through linings etc. The Upholstery Cleaner can be used either with or without the Bonnet (32). For normal cleaning purposes and for general use the Bonnet would be fitted. When removing creases from garments and hanging drapes you can sometimes improve the appearance of the material by using the head without the Bonnet attached. It is best to experiment to get the best finish for you. This tool can also be used either fitted directly onto the Hose Handle or fitted to one or both Extension Tubes. First select which is best for the task in hand and assemble together. HELPLINE NUMBER - TOLL FREE 888 STEAM 12. CALL FIRST IF YOU HAVE ANY PROBLEM 10 Fitting the Bonnet (32) to the Upholstery Cleaner (29) Take the Bonnet, place it on a flat surface with the strings at the top and the nap facing outwards and place the Upholstery Cleaner in the middle. Pull the string until the Bonnet fits tightly to the Upholstery Cleaner, and tie with a bow. When cleaning upholstery you will need to glide the head across the material in the same way as when using the Floor Cleaner. The bonnets will need to be replaced as they become dirty. Wash at 194°F for maximum longevity. Do not use bleach or fabric conditioner and use only one third of normal soap powder to avoid clogging the fibres. Spare Bonnets can be purchased from Earlex Inc or you can make your own using Terry Toweling material. The Upholstery Cleaner can also be used very effectively for removing the creases from hanging drapes. Upholstery Cleaner/Garment Steamer To set up your Steam Dynamo Pro as a Garment Steamer proceed as follows:In the Plug Storage Recess (22) there is a socket (23) to accept the button end of the Extension Tubes. Fit the Extension Tubes together and then locate both into this socket. Now fit the Garment Attachment Rest (30) into the top of the Extension Tube. [. . . ] Refill the Water Tank. Fuse has blown Accessories fall off Water spitting out Not properly fitted Too much water in tank Initial ejection at warm up Not heated up Loud buzzing noise No water in the tank from inside the Steam Unit Steam being emitted from emergency vent at the back of the Water Tank Pressure relief valve is Switch off the unit. operating due to blockage Allow the unit to cool for at least 5 minutes. of steam Check all steam holes in the Attachment, and the Nozzle Connections in the Handle and Extension Tubes being used, to ensure there is no debris or lime-scale preventing steam from passing through them and clean out accordingly. The build up of lime-scale can be avoided by always using cooled, boiled water when filling the Water Tank. SPARE PARTS & ACCESSORIES The following spare parts are available from Earlex Inc. [. . . ]