User manual EASTGEAR HOLUX I6800

[. . . ] Holux i6800 Portable Navigation Device (PND) User Manual Dear User, Thank you for purchasing Holux navigator! Please read this user manual carefully for proper and safe operation of the device. Please use only the original accessories provided to avoid unanticipated damage. Failure to comply with procedures mentioned in this manual or use of accessories or other peripheral devices which are not intended for use with this device will cause the immediate void of product warranty. Please follow local road and traffic rules. [. . . ] Easy to Operate : Touch screen function for ease of operation. Movie Playback : Playback of various movie file formats : ASF, AVI, WMV, MPG, DAT, MPEG & 3GP. Music Playback : Supports music playback in WMA file format. Flash Playback : Supports flash animation playback in SWF file format. High Acoustic Fidelity : Built in high fidelity 1. 5W speaker with dual channel stereo ear piece jack. Photo Viewing : Supports image file viewing in JPG, BMP, GIF & PNG file formats. E-Book Reader : Support txt file format. FM Transmitter : FM transmitter function transmits sound from device to FM receiver in car audio system and broadcasts through the car stereo for louder and clearer audio sounds. Real-time Traffic : Supports external TMC (Traffic Message Channel) High Capacity Battery : 1500 mAh lithium polymer battery, with 2-3 hours of operation on a full charge. Expandable Memory : Supports external memory up to 8GB MicroSD to store data and/or navigation software. __ . 7 1. 4 Specifications Environment Specifications Unit size Operating temperature Storage temperature Operating humidity Storage humidity 130mm x 90mm x 12mm -10°C to +60°C -20°C to +70°C 45% to 80% RH 30% to 90% RH System Specifications CPU speed CPU model Flash memory Storage space External memory Navigation software storage OS 533MHz SIRFATLASIV AT840 DDR 128MB 2GB (Optional) Support up to Max 8GB MicroSD card or NAND Flash WINCE 6. 0 Basic Specifications Screen size Screen resolution Sound quality Sound output Average output Sleep mode power consumption Battery Battery standby 5. 0 800 x 480 Dual channel stereo quality Dual channel 0. 25W/channel, single channel 1. 5W/8 1W <20mW Built-in Lithium Polymer battery 3. 7V 1500mAh Normal use 3 hours(low backlight), standby time 200 hours __ . 8 GPS Hardware Specifications Frequency C/A CODE Satellite Channel Tracking sensitivity Accuracy Acquisition rate Data update rate Re-acquisition time Hot start Warm start Cold start Maximum positioning height Maximum rate Acceleration Built-in antenna type Built-in antenna gain rate 1. 575GHz 1. 023 MHZ chip rate 64 channels -161 dBm 10m, 2D RMS 5m, 3D RMS, WAAS enable 0. 1m/s 1HZ Average 0. 1s Less than 3s Average 30s Less than 60s 18, 000m 515m/s < 4g Built-in antenna 22dB min at 3V Multimedia Functions Specifications Supported music file format Supported video file format Supported ebook file format Supported Flash file format Resolution WMA MPG DAT AVI WMV MPEG 3GP ASF TXT SWF 800*480 FM Transmitter (Optional) Signal frequency Frequency adjustment Distance of transmission 76-108MHz 100KHz 10m __ . 9 2 Quick Start 2. 1 Turning on & off 1) Press and hold "Power" button to turn on the device, it will take about 15 seconds to boot up the system to "Main Menu" interface. 2) Press and hold "Power" button for 1 second to return to the last screen, 3 seconds to go to "Shut down" screen with 3 options to select, "Shut down", "Sleep" and "Return". [Attention] When the battery is low, device will beep to alert user and "Low battery" screen appears. The device will switch off if there is no power supply. If device cannot turn on, please check if the battery is low. 2) Do not eject MicroSD card during operation (eg. 3) Do not store card in high temperature or in any moist environment. 4) Avoid liquid and corrosive material. 2. 6 Start Navigation (Should be set at factory level) Navigation is the main function of this GPS device, here is the introduction of 5 simple steps on operating navigation system. Step 1: Setting navigation path 1) Tap the "Settings" icon in Main Menu (as shown below). 2) Tap "Navi Path" icon to access navigation software path (as shown below). __ . 12 3) Tap to browse and select the directory. 4) Select the navigation software (filename with extension of . exe) and click to save (as shown below). We recommend you tap for "Navigation Autorun at Power on". Navigation software auto-starts when the device is turned on. 5) Click to go back to previous menu. Step 2: Locating GPS current location In "Main Menu, click "Navigation" to run navigation software on the device. Navigation software will search for satellites during start-up. The GPS device may take 2-3 minutes depending on the search process. [. . . ] There are 2 mode of USB connection with PC, tap "Settings" and tap connection mode (as shown below). to select Tap "Mass Storage" mode and tap to save and exit. "Mass Storage" mode - The device is connected to PC via USB cable to directly access the content of SD card and FLASH memory in the device. The device is used as a memory card reader; "MS ActiveSync" mode - The device is connected to PC via USB cable which allows the PC to synchronize information automatically with the device. MicroSD card FLASH memory in the device can be accessed by PC. [. . . ]