User manual EDIROL CG-8

[. . . ] 201b Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 4), "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, OWNER'S MANUAL should be read in its entirety. [. . . ] Alternatively, you can press the [MENU] button to return to Play mode. Guide 3 4 Turn the VALUE dial to move the guide, and select the project into which you want to load a Photo Picture or Stamp Picture. ] buttons to select "EDIT PROJECT, " and press the You can't select a project that is not assigned to a visual pad (p. 54). The EDIT PROJECT screen will appear. fig. material-assign01. e. eps If in step 3 you select a visual pad to which no project is assigned (displayed as "---"), the message "No project assigned" will appear. Press the [ENTER] button to return to the PROJECT EDITOR screen. Guide 58 About projects 5 Turn the VALUE dial to move the guide, and select the visual pad ([1]­[16]) to which you want to assign a Photo Picture or Stamp Picture. You can also use the [VALUE] knob to move between the tabs. When the guide passes [16] you will move to the next tab. Conversely, when the guide passes [1] you will move to the preceding tab. "PHOTO-1" "PHOTO-2" "PHOTO-3" "STAMP" Photo Picture bank 1 Photo Picture bank 2 Photo Picture bank 3 Stamp Picture The locations corresponding to visual pads to which a Photo Picture or Stamp Picture is already assigned will show that image. This will be blank if no Photo Picture or Stamp Picture is assigned. The position of the pictures shown in the screen corresponds to the location of the visual pads. 6 Use the [ PREV][NEXT the [ENTER] button. ] buttons to choose "ASSIGN PICTURE, " and press The picture select screen will appear. 7 Select a Photo Picture or Stamp Picture. Example: the screen for selecting a Photo Picture fig. material-assign02. e. eps Make your selection using the [ PREV][NEXT ] buttons, then press the [ENTER] button to confirm your choice. Cancel the operation and return to the EDIT PROJECT screen. Enter the folder selected in the list. Return to the next higher level. Shows information about the picture selected in the list. Indicates the current level. List Turn the [VALUE] dial to select. 59 About projects Selecting an image or folder on the internal hard disk Use the [ PREV][NEXT ] buttons to select "UPTO, " and press the [ENTER] button several times to select the "Internal" folder located at the top of the hierarchical folder structure. Selecting an image or folder on a CompactFlash card in the card adaptor (included) Use the [ PREV][NEXT ] buttons to select "UPTO, " and press the [ENTER] button several times to select the "External" folder located at the top of the hierarchical folder structure. About the displayed icons · If you select "PHOTO-1"­"PHOTO-3" in step 5: The list will show JPEG files ( · If you select "STAMP" in step 5: The list will show PNG files ( (. jpg)) and folders ( ). Files on the CompactFlash card whose filenames contain characters that cannot be used on the CG-8 (i. e. , characters other than A­Z, a­z, 0­9, -, _), or files that were saved without a filename extension will not be displayed on the CG-8. (. png)) and folders ( ). 8 Use the [ button. PREV][NEXT ] buttons to select "SELECT, " and press the [ENTER] If in step 5 you selected a pad to which a Photo Picture or Stamp Picture was already assigned, the image will be replaced. (This merely replaces the assignment; the picture itself will not be overwritten. ) You will return to the EDIT PROJECT screen. The picture you selected in step 7 will be assigned to the visual pad you selected in step 5. Inserting a blank space between pictures If you want to assign a new picture between two pictures, you'll need to first create a blank space between the currently assigned visual pads, and then assign the desired picture. In the EDIT PROJECT screen, turn the [VALUE] dial to move the guide, and select the location at which you want to assign a new picture. Use the [ PREV][NEXT the [ENTER] button. ] buttons to select "INSERT SPACE, " and press The message "Insert assignment space. Use the [ PREV][NEXT ] buttons to select "OK, " and press the [ENTER] button. If you decide to cancel the operation, choose "CANCEL. " A blank space will be created at the location you selected, and subsequent pictures will be reordered. * Be aware that at this time, any Photo Picture or Stamp Picture that was assigned to visual pad [16] will be deleted. The bank will not change. 4. 5. Assign the desired picture as described in step 6 and following of "Assigning a Photo Picture or Stamp Picture to a visual pad" (p. 57). Deleting the picture assignment from a visual pad 1. In the EDIT PROJECT screen, turn the VALUE dial to move the guide, and select the picture whose assignment you want to delete. Use the [ PREV][NEXT ] buttons to select "REMOVE ASSIGNMENT, " and press the [ENTER] button. [. . . ] Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit. For Canada NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below. Information EUROPE EDIROL (Europe) Ltd. Studio 3. 4 114 Power Road London W4 5PY U. TEL: +44 (0)20 8747 5949 FAX:+44 (0)20 8747 5948 http://www. edirol. com/europe Deutschland TEL: 0700 33 47 65 20 France TEL: 0810 000 371 Italia TEL: 02 93778329 U. / CANADA EDIROL Corporation North America 425 Sequoia Drive, Suite 114 Bellingham, WA 98226 U. [. . . ]