User manual EDIROL FA-66

[. . . ] OWNER'S MANUAL 201a Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, OWNER'S MANUAL should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2005 ROLAND CORPORATION All rights reserved. [. . . ] 12) so it's positioned to the left of the MIX (center) position. About the demo songs The SampleSong folder on the included CD-ROM contains the following demo songs. Please copy the demo songs to the hard disk of your computer before listening to them. * The demo songs were produced at 48 kHz. You must set the FA-66's sample rate to 48 kHz. You'll need to cycle the power to the FA-66 after changing the sampling rate. for Cubase folder This folder contains the demo songs as Cubase VST song files (. all) and Cubase SX project files (. cpr). If you are using the Cubase SX demo version, the playback will not be correct since some functionality (such as effects) will not be available. for SONAR folder This folder contains the demo songs as SONAR project files (. cwb). 33 Installing the driver (Windows) Software settings Before you start up your software, use a FireWire (IEEE 1394) cable to connect the FA-66 to your computer, and turn on the power of the FA-66. If your software allows you to specify MIDI and audio input/output settings, choose EDIROL FA-66. For details, refer to the owner's manual for your software. Also refer to "Software settings" (p. If you have turned on software monitoring in your application, turn the FA-66's hardware monitoring (direct monitor) off to prevent double monitoring and to keep an audio feedback loop from occurring. For the latest information, please visit http://www. edirol. com/ 34 Basic connections and settings This section explains basic connections and data flow for the FA-66. Refer to the block diagram printed on the front cover of the manual as you read this section. * Before making connections to other equipment, turn down the volume of all your equipment and turn off the power to avoid causing malfunctions or damaging your speakers. * When connection cables with resistors are used, the volume level of equipment connected to the inputs (Input jacks) may be low. If this happens, use connection cables that do not contain resistors, such as those from the Roland PCS series. Basic connections Use a FireWire (IEEE 1394) cable to connect the FA-66 to your computer. MIDI data and audio data are transferred in both directions via the FireWire (IEEE 1394) cable. By connecting headphones or monitor speakers as shown in the diagram below, you can monitor the playback from your software or the sound from an instrument or audio device connected to the FA-66. fig. basic Amplified speakers FireWire (IEEE1394) connector IEEE1394 connector (FireWire connector, iLink connector, DV connector) FireWire cable Headphones Computer 35 Basic connections and settings Recording a mic or guitar Here's how to make connections and settings to let you sing or play your guitar while listening to audio data on your computer, and record just the vocal or guitar into your sequencer. fig. mic-guitar Guitar/bass Adjust the level so that the red (far right) does not light Monitor in stereo Connect to INPUT 2 Hi-z Monitor in monaural Switch to ON only if you're using condenser mics When using a mic for input, it's a good idea to switch this ON Adjust the input level Adjust the input level Turn the knob toward the right if you want the sound from the input jacks to be louder than the playback from the computer. Specify the sample rate Turn this all the way toward the left Connections The sound of the mic connected to INPUT 1 will be recorded in your computer as the left (L) channel. If you connect a source to INPUT 2, it will be recorded on the right (R) channel. Connect your guitar to INPUT 2. Sample rate select switch Set this to the same sample rate as selected in your recording software. If you switch the FA-66's sample rate, you must turn the power of the FA-66 off, then on again to get the setting to take effect. Input impedance select switch If you've connected a mic to INPUT 2 Select Lo-Z. If you've connected a guitar to INPUT 2 Select Hi-Z. STEREO/MONO select switch (direct monitor section) Set this according to whether you want to monitor the input signal in stereo or in monaural. 36 Basic connections and settings Direct monitor soft control switch Turn this on if you want to control input monitoring from ASIO 2. 0 compatible software. Direct monitor volume This adjusts the balance between the monitor volume and the audio playback volume from your computer. [. . . ] Paseo García Faria, 33-35 08005 Barcelona SPAIN TEL: 93 493 91 00 AFRICA EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 QATAR Badie Studio & Stores P. O. Box 62, Doha, QATAR TEL: 423554 THAILAND Theera Music Co. 330 Soi Verng NakornKasem, New Road, Sumpantawongse, Bangkok 10100, THAILAND TEL: (02) 224-8821 HONDURAS Almacen Pajaro Azul S. A. BO. Paz Barahona 3 Ave. 11 Calle S. O San Pedro Sula, Honduras TEL: (504) 553-2029 CZECH REP. K-AUDIO Kardasovska 626. [. . . ]