User manual EDIROL V-44SW

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. 6­7), and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] S-Video: Only the input from the S-VIDEO IN connector is selected. Composite: Only the input from the COMPOSITE IN connector is selected. Brightness adjustment Contrast adjustment Saturation adjustment Hue adjustment Sets the Enable/Disable status for the channel select buttons For more detailed information, refer to the column, "To Prevent Errors in Using the Channel Select Buttons" (p. The sub-menu settings are returned to their factory default settings ( p. 29). 2: SD Brightness 3: SD Contrast 4: SD Saturation 5: SD Hue 6: SD Sw Enable 7: SD Reset 34 Setting the Input and Output Selecting NTSC or PAL Format The V-44SW's input and output formats are selectable; you can specify the NTSC format used in Japan and the United States or the PAL format used in Europe. Switch to the format suited to your needs. Switching the input and output formats also switches the frame rate of the output format of component (p. With NTSC format: With PAL format: Frame rate of "60" frames per second Frame rate of "50" frames per second Displaying a Test Pattern You can display a test pattern (color bars), useful and convenient in adjusting the image quality of the display. 1 2 3 Press the [MENU] button to display the Main menu. Output" and select "14: Test Pattern Select" from the sub-menu. Select the test pattern to be displayed. The test pattern (color bars) is output. Value Displayed (No output) 1 2 3 Press the [MENU] button to display the Main menu. System" and select "1: System Frame Rate" from the sub-menu. Set each parameter to "60-NTSC" or "50-PAL. " 60-NTSC: NTSC format 50-PAL: PAL format Off 75% Color Bar 100% Color Bar 35 Switching Video Selecting the Video Switching Mode The V-44SW features two different video switching modes, "Direct mode" and "Preset mode. " Each mode functions in switching video as follows. Switching Video in Direct Mode Immediately after the power is turned on, SD VIDEO Channel 1 is assigned as the final output. 1 Press one of the SD VIDEO buttons [1]­[4] or one of the HD/RGB buttons [1]­[4] to select the channel. The selected button lights up, and the final output video is switched. Lit Direct Mode The final output video is switched when channels are selected with the press of a single button. Final Output Video Preset Mode When a channel is selected, the video in the preview monitor switches. Pressing the [TAKE] button confirms selection of this as the output video, switching the final output video. Preview Final Output Video Selecting an HD/RGB channel to which no signals are input may result in delayed switching of the video. About the Indicators Whenever video is being input to a channel, its indicator lights up. You can determine the type of video signal being input by observing the color of the indicator. Indicator Lit (Red) Lit (Green) Lit (Green) SD VIDEO1­4 Composite signal S-video signal No signal input HD/RGB1­4 RGB signal Component signal No signal input Selecting the Video Switching Mode 1 2 3 Press the [MENU] button to display the Main menu. System" and select "7: Panel Operation Mode" from the sub-menu. Select "Direct Mode" or "Preset Mode. " Direct Mode:video is switched in Direct mode. Preset Mode:video is switched in Preset mode. About the Colors of Channel Select Buttons You can change the colors in which channel select buttons light. 1 2 3 Press the [MENU] button to display the Main menu. System" and select "8: Input Sw LED Color" from the sub-menu. Select the colors for the channel select buttons. About the Effects Used in Switching Screens You can apply the screen transition effects, regardless of the mode used for switching the video. For more detailed instructions, refer to "Selecting the Effects To Be Applied in Switching" (p. 38). "Sub" refers to the colors in which LEDs light when video is selected in the Picture in Picture sub-screen (p. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. [. . . ]