User manual EHLEVA STILO 83

[. . . ] advanced mobular stair system MC Code MD. K. 007 Rev 00 Edition 11. 2008 - STILO 70 - STILO 83 advanced mobular stair system CONTENTS Structure of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wooden components VECTOR 70 - VECTOR 83. " Components VECTOR 70 - VECTOR 83. [. . . ] To define the number of spacers to be used, refer to the "table A" attached to the pages 9-10-11. Form the spacer package by assembling the P106 - P106a spacers as shown in fig. 12. P106a K104 P106 K120 Insert the K120 plate into the K101 support module and maintain its position by means of the D04 template as shown in fig. Screw the K104 pin into the K120plate described above as shown in fig. 12 - 18 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 www. ehleva. com ehleva@ehleva. it By Mobirolo S. p. A. STILO 70 - STILO 83 - STILO 70 - STILO 83 advanced mobular stair system Having formed a unit, insert the projecting part of the pin into the hole placed under the step support module mounted previously. Insert the K119 plate into the pipe of the unit described above and anchor everything by means of the K127 screw and the K126 washer. To facilitate screwing operations, we recommend using a jack spanner to screw in the screw until it starts tightening. Since the tread must still be adjusted, the unit must not be tightened fully. Moreover, before assembling the module, insert the P105 plug from behind. 13 Now adjust the module according to the "P" tread size. This value must be measured starting from the front part of the spacer package until the reference present on the support flange as shown in fig. Fully tighten the K127 screw which was previously left lose, paying particular attention to the position of the spacer package, which needs to remain aligned with the support. The use of a rigid reference guide is recommended to be applied to the sides of the pipe with clamps during the operation. Fig. 14 Assemble the L20 step on the K101 support by means of the B205 screws as shown in fig. 15 Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 www. ehleva. com ehleva@ehleva. it By Mobirolo S. p. A. STILO 70 - STILO 83 - 19 - - STILO 70 - STILO 83 advanced mobular stair system Insert the K63 column into the P107 support mounted previously. By means of a level check that it is vertical and lock it temporarily in the position illustrated in fig. Insert a P107 support and mark the position of the holes on the bottom part of the step fig. 16 B203 Drill in the points marked and mount the P107 support by following the same procedure illustrated above. 18 B204 STILO 70 - STILO 83 - 20 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 www. ehleva. com ehleva@ehleva. it By Mobirolo S. p. A. - STILO 70 - STILO 83 advanced mobular stair system Continue assembling the following steps P Max according to the same procedure until the first STILO 70= 230 mm L21 is achieved where the staircase starts turning. [. . . ] +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 www. ehleva. com ehleva@ehleva. it By Mobirolo S. p. A. - 29 - - STILO 70 - STILO 83 advanced mobular stair system ASSEMBLING THE HANDRAIL Place the handrail on the first support approx. 40-50 mm far from the first column (fig. 37) By referring to the housing, drill a Ø3 preliminary hole to anchor the handrail in its K65 housing. Make sure that it is correctly placed into its housings, no gaps are left between them Anchor the handrail by means of the dedicated K66 kit screw. [. . . ]