User manual EHLEVA VECTOR 80

[. . . ] advanced mobular stair system MC Code MD. K. 001 Rev 02 Edition 02. 2009 - VECTOR 80 advanced mobular stair system CONTENTS Structure of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " Useful height measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To anchor the module, two holes are enough. Identify the holes that need to be reproduced: in general refer to those halfway the floor slab width, not too close to the floor surface. 5 - 16 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. VECTOR 80 - VECTOR 80 advanced mobular stair system PREPARING COLUMNS AND STEPS Before proceeding to assemble the steps, mount the P107 banister column support fig. Drill a Ø4 hole by means of a wood drill in the points identified on the step and achieve a 30 mm depth as shown in fig. Be very careful when operating on the bottom side of the step, where anchoring holes are already present, and on the correct side where the banister will be mounted. Fig. 6 VECTOR 80 Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. Fig. 10 - 17 - - VECTOR 80 advanced mobular stair system ASSEMBLING THE STEP L20 B205 P107 Fig. 11 At this point form the P106 - P106a spacer package which will determine the size of the rise set previously. To define the number of spacers to be used, refer to the "table A" attached to the pages 9-10-11. Form the spacer package by assembling the P106 - P106a spacers as shown in fig. 12. P106a K104 P106 Insert the K120 plate into the K101 support module and maintain its position by means of the D04 template as shown in fig. Screw the K104 pin into the K120plate described above as shown in fig. 12 - 18 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. VECTOR 80 - VECTOR 80 advanced mobular stair system Having formed a unit, insert the projecting part of the pin into the hole placed under the step support module mounted previously. Insert the K119 plate into the pipe of the unit described above and anchor everything by means of the K127 screw and the K126 washer. To facilitate screwing operations, we recommend using a jack spanner to screw in the screw until it starts tightening. Since the tread must still be adjusted, the unit must not be tightened fully. Moreover, before assembling the module, insert the P105 plug from behind. 13 Now adjust the module according to the "P" tread size. This value must be measured starting from the front part of the spacer package until the reference present on the support flange as shown in fig. [. . . ] All configurations envisage that an additional column must be mounted on the last straight step before the staircase turns. Figure 38 shows the example of a "U" staircase. L15 B301 K71 K77 L15 L15 L15 K80 Ø3 K65 Fig. 37 Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. VECTOR 80 - 29 - - VECTOR 80 advanced mobular stair system After having assembled the handrail the K68 plug must be mounted at both ends. [. . . ]