User manual EHLEVA VENUS

[. . . ] " Calculating the tread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " Calculating the rise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . " Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 80 L=840 X 1940-2090 Y 1640 Z 1100 VEC. 80 L=840 X 1720-1840 Y 1640 Z 1320-1350 VEC. for the VECTOR 83 model (side without banister) value A = corresponding to the value of the "A" rise calculated previously. To anchor the module, two holes are enough. Identify the holes that need to be reproduced: in general refer to those halfway the floor slab width, not too close to the floor surface. 5 - 16 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. VENUS - VENUS advanced mobular stair system PREPARING COLUMNS AND STEPS Before proceeding to assemble the steps, mount the P107 banister column support fig. Drill a Ø4 hole by means of a wood drill in the points identified on the step and achieve a 30 mm depth as shown in fig. Be very careful when operating on the bottom side of the step, where anchoring holes are already present, and on the correct side where the banister will be mounted. Fig. 6 VENUS Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. Fig. 18 B204 VENUS - 20 - Via C. Colombo, 22/A - 42046 - Reggiolo - Reggio Emilia - Italy Tel. +39 - 0522-97 32 34 - Fax +39 - 0522-97 31 39 ehleva@ehleva. it By Mobirolo S. p. A. - VENUS advanced mobular stair system Continue assembling the following steps P Max according to the same procedure until the first L21 is achieved where the staircase starts Vector 80= 250 mm turning. Mount the P107 support on the L21 step by using the pre-existing holes and make sure to insert the square nut with relevant security dowel as illustrated above. Inset a K63banister column into the top step support and lock it temporarily in the position illustrated in fig. Check that the module is positioned in the P Max tread position, then place the L21 step as shown in fig. 19 and lock it by means of B205 Adjust the step in the maximum tread position, i. e. all the way in the front, until the most advanced position is achieved. 19) L21 Lock the module in the position achieved and make sure that during the operation the spacer package remains aligned with the module, including the vertical direction of the column. WARNING!!!While the steps are being assembled, the unit that is being formed should be supported so that it does not press on the support of spacer package (see the "SUPP. " example fig. This should be done every three/four steps (see Example in fig. 20) to facilitate assembling the starting module after having reached the ground. K63 P107 Fig. 19 P Min Vector 80= 220 mm Similarly, proceed to assemble the L23 central step. [. . . ] When assembling the handrail make sure that the k65 supports shaped like a "saddle" face the inner part of the staircase. After having reached the last column before the staircase turns, cut the handrail and leave the exceeding part so that the K68 plug can be mounted. We suggest to mount the plug before the final anchoring of the handrail on the column. Resume assembling the handrail after the staircase has turned by proceeding in the same way until reaching the last column mounted on the final step. Cut the excessive part of the handrail and leave a 40-50 mm projecting part. [. . . ]