User manual EINHELL BG-GC 80

[. . . ] The equipment must never run dry or be used when the intake line is closed fully. The manufacturers warranty does not cover damage caused to the equipment as a result of running it dry. The pump must not be used to operate swimming pools. The equipment must not be installed in the drinking water pipe line. [. . . ] Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. Before putting the equipment into operation 5. 1 Connecting the intake line As a basic principle, we recommend the use of a preliminary filter and a suction set with suction hose, suction strainer and non-return valve, in order to prevent long priming periods and unnecessary damage to the pump as a result of stones and solid foreign bodies. 3/4" plastic hose with spiral reinforcement) either directly or with a threaded nipple to the pumps intake connection (1" IG) (see Fig. If the intake valve cannot be used, a check valve should be installed in the intake line. Position the intake line so that it rises from the water withdrawal point to the equipment. Avoid positioning the suction pipe higher than the pump, as this would delay the escape of air bubbles from the suction pipe and impede the priming process. Install the intake and discharge lines in such a way that they do not exert any mechanical pressure on the equipment. In order to ensure a long service life, however, we recommend that you regularly check and care for the product. The equipment must be disconnected from the power supply (pull the power plug) prior to performing any maintenance. 1 Servicing If the equipment becomes clogged, connect the discharge line to the water line and disconnect the suction hose. Replacing the mains cable: Important: Disconnect the equipment from the power supply! a defective mains cable may only be replaced by a qualified electrician. There are no parts inside the equipment which require additional maintenance. Faults Motor fails to start up Cause - No mains voltage - Pump rotor blocked -thermostat switched off No intake - Intake valve not in water - Pump chamber without water connection - Air in intake line air-tight - Intake valve leaks - Strainer (intake valve) blocked - Max. Suction height exceeded Inadequate delivery rate - Suction height too high - Strainer dirty - Water level falling rapidly - Pump performance diminishedby contaminants part Thermostat switches pump off - Motor overloaded - friction caused by foreign substances too high Remedy - Check voltage - Dismantle and clean pump - Immerse intake valve in water - Fill water into intake - Make sure intake line is close - Clean intake valve - Clean strainer - Check suction height - Check suction height - Clean strainer - Immerse intake valve deeper - Clean pump and replace wearing - Dismantle and clean pump. K t p erklärt folgende Konformität gemäß EU-Richtlinie und Normen für Artikel declares conformity with the EU Directive and standards marked below for the article déclare la conformité suivante selon la directive CE et les normes concernant larticle verklaart de volgende conformiteit in overeenstemming met de EU-richtlijn en normen voor het artikel declara la siguiente conformidad a tenor de la directiva y normas de la UE para el artículo declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo förklarar följande överensstämmelse enl. T For EU countries only Never place any electric tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e. [. . . ] The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. no guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. [. . . ]