User manual EINHELL BT-JS 800 E

[. . . ] Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 1 k Bedienungsanleitung Elektronik-Stichsäge Operating Instructions Electronic Jigsaw Mode demploi de la scie à guichet électrique Istruzioni per luso per seghetto alternativo elettronico Betjeningsvejledning Elektronisk stiksav Használati utasítás Elektronika-szúrófrész Upute za uporabu Elektronicka ubodna pila Uputstva za upotrebu Elektronska ubodna testera Návod k obsluze Elektronická pímocará pila Návod na obsluhu Elektrická priamociara píla t p C l L A B f 4 j W Art. -Nr. : 43. 211. 20 I. -Nr. : 01017 BT-JS 800 E Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 2 1 1 3 2 4 5 17 16 15 14 6 13 12 10 9 8 7 18 11 2 12 10 2. 3 8 14 14 1. 12 10 2 Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 3 4 5 4 13 7 13 11 7 18 6 7 9 7 6 7 8 1 9 17 + 2 3 16 3 Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 4 10 11 12 4 Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 10 GB "Caution - Read the operating instructions to reduce the risk of inquiry" Wear ear-muffs. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Wear safety goggles. [. . . ] 8/Item 2) You can lock the ON/OFF switch (3) using the locking button (2) when the equipment is in operation. To switch off the equipment briefly hold down the ON/OFF switch (3). Anleitung BT-JS 800 E_SPK1:_ 15. 09. 2008 13:31 Uhr Seite 13 GB 6. 3 Electric speed selector (Fig. 8/Item 1) You can pre-select the required speed with the speed selector. Turn the speed selector in PLUS director to increase the speed and turn the speed selector in MINUS direction to reduce the speed. The suitable stroke speed is dependent on the relevant material and working conditions. General rules for cutting speeds for metal cutting work must be complied with here as well. You can generally use a higher speed with fine saw blades whilst coarser saw blades require lower speeds. Position 1-2 = low stroke speed (for steel) Position 3-4 = medium stroke speed (for steel, soft metal, plastic) Position 5-6 = high stroke speed (for softwood, hardwood, soft metal, plastic) 6. 4 Setting the pendulum action (Fig. 3/Item 8) The strength of the pendulum action of the saw blade (12) can be adjusted using the selector switch for pendulum action (8). You can adjust the cutting speed, the cutting performance and the finish to the workpiece you wish to saw. Set the selector switch for pendulum action (8) to one of the following positions: Position 0: No pendulum action Material: Rubber, ceramic, aluminium, steel Please note: For fine and clean cuts, thin materials (e. g. Position 1: Small pendulum action Material: Plastic, wood, aluminium Please note: For hard materials Position 2: Medium pendulum action Material: Wood Position 3: Large pendulum action Material: Wood Please note: For soft materials and sawing along the grain The best combination of speed and pendulum action depends on the material you wish to saw. We recommend you to make a trial cut on a waste piece in order to check the ideal settings. 9/Item 16) The LED lamp (16) can be used in poor lighting conditions to additionally illuminate the cutting position. To switch off, press the switch (17) again. 6. 6 Making cuts Ensure that the ON/OFF switch (3) is not depressed. Only then should you connect the mains plug to a suitable socket. Do not switch on the jigsaw until you have fitted a saw blade. Use only saw blades that are in perfect condition. Replace blunt, bent or cracked saw blades immediately. Place the saw foot flat on the workpiece you wish to saw. Allow the saw blade to accelerate until it reaches full speed. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]