User manual EINHELL BT-MG 180

[. . . ] Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:47 Uhr Seite 1 Bedienungsanleitung Multifunktionswerkzeug t p C Operating Instructions Multifunction Tool Mode d'emploi Outil multifonction Istruzioni per l'uso Utensile multifunzione lL Betjeningsvejledning Multifunktionsværktøj A Kezelési útmutató Többfunkciós szerszám Bf Upute za uporabu Visefunkcijski alat 4 j W Uputstva za upotrebu Visefunkcijski alat Návod k obsluze Víceúcelové náadí Návod na obsluhu Multifunkcné náradie Art. -Nr. : 44. 650. 00 I. -Nr. : 01018 BT-MG 180 Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:48 Uhr Seite 2 1 1 3 4 2 7 5 6 9 8 2 3 9 b b 8 9 a 7 6 2 Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:48 Uhr Seite 3 4 3 5 5 3 b a 4 2 2. c 1. 6 1 3 Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:48 Uhr Seite 9 GB Table of contents 1. Safety regulations Layout Intended use Technical data Before starting the equipment Starting up Replacing the power cable Cleaning, maintenance and ordering of spare parts Disposal and recycling 9 Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:48 Uhr Seite 10 GB "Caution - Read the operating instructions to reduce the risk of inquiry" Wear ear-muffs. The impact of noise can cause damage to hearing. Wear a breathing mask. [. . . ] 6. 2 Practical tips Switch on the equipment. Never move your hands into the direct vicinity of the work area. Use only plug-in tools which are in good working order and undamaged. 6. 2. 1 Plug-in tools Sawing: Sawing wood and plastic. Notes on working practice: When sawing, watch out for foreign bodies in the workpiece and remove these if necessary. Plunge cutting is allowed only in soft materials such as wood or plasterboard. Sanding/grinding: Surface sanding/grinding at edges, in corners or hard-to-reach areas. Depending on choice of sanding/grinding paper for the sanding/grinding of wood, paint, lacquer, etc. Notes on working practice: This equipment offers particularly high performance for the sanding/grinding of hard-to-reach corners and edges. To sand/grind profiles and channels you can also work with just the tip or the edge of the sanding/grinding disk. Various sanding/grinding papers are available, specially designed for the different types of material you may be working on and the amount you wish to remove from the surface. The amount removed will depend largely on the choice of sanding/grinding paper and pressure applied to the sanding/grinding disk. Scraping: Scraping off old paint or adhesives. Notes on working practice: Move the plug-in tool against the area you want to remove. Begin with a flat angle of incidence and little pressure. wood, plaster) may be damaged if too much pressure is used. 7. Replacing the power cable If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its aftersales service or similarly trained personnel to avoid danger. Anleitung_BT_MG_180_E_SPK1:_ 03. 06. 2008 14:48 Uhr Seite 13 GB 8. Cleaning, maintenance and ordering of spare parts Always pull out the mains power plug before starting any cleaning work. 8. 1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Clean the equipment regularly with a moist cloth and some soft soap. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]