User manual EINHELL BT-PL 750

[. . . ] Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:05 Uhr Seite 1 Bedienungsanleitung Elektro-Handhobel t p C Operating Instructions Hand-Held Electric Plane Mode demploi Raboteuse électrique à main Istruzioni per luso Piallatrice elettrica lL Betjeningsvejledning Elektrisk håndhøvel A Használati utasítás Elektromos - kézigyalu Bf Upute za uporabu Elektricna rucna blanjalica 4 j W Uputstva za upotrebu Elektricna rucna rendisaljka Návod k obsluze Elektrický rucní hoblík Návod na obsluhu Elektrický rucný hoblík Art. -Nr. : 43. 452. 61 I. -Nr. : 01017 BT-PL 750 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:05 Uhr Seite 2 1 2 7 6 4 10 3 1 6 8 7 2 9 3 2 11 13 5 12 2 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:05 Uhr Seite 3 4 5 2 7 1 6 7 9 7 7 a 13 b d c 8 3 4 9 a 3 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:06 Uhr Seite 4 10 11 11 12 12 c 13 c c a 14 a 15 d 6 4 b c Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:06 Uhr Seite 10 GB "Caution - Read the operating instructions to reduce the risk of inquiry" Wear ear-muffs. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Wear safety goggles. [. . . ] Release the locking screw (11) and position the step depth scale (12) so that the required step depth is displayed. Width of step: You can set the width of the step with the parallel stop (13). 12 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:06 Uhr Seite 13 GB Depth of step: We recommend you to set a cutting depth of 2 mm and to keep planing the workpiece until the required depth of step is reached. wrench (a) supplied and push the carbide metal reversible knife out of the planing shaft using a piece of wood. Check that the planing knife conforms with both ends of the planing shaft. Always replace both knives to ensure a uniform chip depth. Important: Before using the hand-held electric plane make sure the knives are installed securely and in the right place. 13) (8) Front base plate (moving plane shoe) (5) Rear base plate (fixed plane shoe) 1. Correct adjustment Result: Smooth planed surfaces 2. Notches in the surface Problem: The cutting edge on the planing knife (or both planing knives) is not parallel to the height of the rear base plate. 7. Replacing the power cable If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its aftersales service or similarly trained personnel to avoid danger. 8. Cleaning, maintenance and ordering of spare parts Always pull out the mains power plug before starting any cleaning work. 8. 1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. 8. 2 Carbon brushes In case of excessive sparking, have the carbon brushes checked only by a qualified electrician. The carbon brushes should not be rep laced by anyone but a qualified electrician. 12-13) Important: Always pull the plug out of the power socket before doing any work on the equipment. To change the planing knives, use the supplied wrench (a). The hand-held electric plane comes with two carbide metal reversible knives. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]