User manual EINHELL BT-RO 1200 E

[. . . ] Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 1 Bedienungsanleitung Elektro-Oberfräse t p C Operating Instructions Electric Router Mode demploi Défonceuse électrique Istruzioni per luso Fresatrice verticale elettrica lL Betjeningsvejledning Elektrisk overfræser A Használati utasítás Villamos -felsmaró Bf Upute za uporabu Elektricna glodalica za izradu utora 4 j W Uputstva za upotrebu Elektricna glodalica za izradu utora Návod k obsluze Elektrická horní frézka Návod na obsluhu Elektrická horná frézka Art. -Nr. : 43. 504. 80 I. -Nr. : 01017 BT-RO 1200 E Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 2 1a 6 7 8 5 7 4 9 10 3 2 1 1b 19 11 1c 22 18 17 20 16 12 3 23 13 21 14 15 2 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 3 2 3 1 1B 1A f 2 4 5 3 3 b a 2 b a 21 b a 2 3 c 13 6 20 7 c 20 f 2 d e b 3 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 4 8 12 9 23 10 10 12 11 12 22 10 12 13 15 9 14 4 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 5 14 19 15 18 17 16 15 14 16 5 17 11 + -- 4 18 19 a c b c 5 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:33 Uhr Seite 13 GB Important!When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times. [. . . ] Undo the wing screw (16) and fixing handle (9). Slowly move the machine downwards until the cutter makes contact with the workpiece. Set the depth stop (19) to the required routing depth using the scale and secure it with the wing screw (16). Test the setting by completing a test cut on a waste piece. 6. 4 Routing To avoid damage to the router, make sure there are no foreign objects attached to the workpiece. Connect the mains plug to a suitable socket. Hold the tool using both of its handles (7). Set the cutting depth as described in point 6. 3. Select the speed as described in point 6. 2 and switch the machine on (see point 6. 1). Test the machine settings using a piece of waste. Only then should you lower the router to its working height and lock the machine with the locking grip (9). Cutting direction: The cutting tool turns clockwise. To avoid accidents you must always cut against the direction in which the tool turns (Fig. Feed speed: It is very important to machine the workpiece at the correct feed speed. We recommend that before you machine the actual workpiece, you carry out several trial cuts on a waste piece of the same type. This will enable you to find the best working speed for the workpiece very easily. Feed speed too low: The cutter could heat up excessively. If you are cutting inflammable material such as wood, the workpiece could ignite. 6. Operation Never use a low quality or damaged cutter. Use only cutting tools with a shaft diameter of 6 mm or 8 mm. The cutters must also be designed for the appropriate idling speed. Secure the workpiece so that it cannot be thrown through the air as you work on it. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]