User manual EINHELL BT-TS 800

[. . . ] Anleitung BT-TS 800_SPK1:_ 25. 09. 2007 9:09 Uhr Seite 1 Bedienungsanleitung Tischkreissäge Operating Instructions Bench-Type Circular Saw Mode demploi Scie circulaire à table de menuisier Istruzioni per luso della Sega circolare da banco. Brukerveiledning Bordsirkelsag A B f 4 Használati utasítás asztali körfrész Naputak za upotrebu stolne kruzne pile Uputstva za upotrebu stone kruzne testere Návod k pouzití Univerzální kotoucová pila Návod na obsluhu Stolná kotúcová píla j W Art. -Nr. : 43. 407. 60 I. -Nr. : 01017 BT-TS 800 Anleitung BT-TS 800_SPK1:_ 25. 09. 2007 9:09 Uhr Seite 2 Vor Inbetriebnahme Bedienungsanleitung und Sicherheitshinweise lesen und beachten Read and follow the operating instructions and safety information before using for the first time. Avant la mise en service, lisez le mode demploi et les consignes de sécurité et respectez-les. Prima della messa in esercizio leggete e osservate le istruzioni per luso e le avvertenze di sicurezza. [. . . ] 24 mm 505 x 335 x 320 mm 10 kg Load factor: A load factor of S2 10 min (intermittent periodic duty) means that you may operate the motor continuously at its nominal power level (800 W) for no longer than the time stipulated on the specifications label (10 minutes ON period). If you fail to observe this time limit the motor will overheat. During the OFF period the motor will cool again to its starting temperature. Anleitung BT-TS 800_SPK1:_ 25. 09. 2007 9:09 Uhr Seite 12 GB time after changing the saw blade. 4) Mount the saw blade guard (2) on the splitter (5) and align. Insert the screw (15) through the hole in the saw blade guard (2) and in the splitter (5) and secure it with the nut. To remove the saw blade guard, proceed in reverse order. Take off the saw blade guard (2) (see 7. 3). Lift the worn table insert (6) up and out. Fit a new table insert in reverse order. 9/10) Slacken the star-grip screws (14). You can now adjust the blade (4) to the required angle (see scale (13)) by sliding the two star-grip screws (14). Re-tighten the star-grip screws (14). 9. Sawing operations After each new adjustment it is advisable to carry out a trial cut in order to check the set dimensions. After switching on the saw, wait for the blade to reach its maximum speed of rotation before commencing with the cut. Secure long workpieces against falling off at the end of the cut (e. g. with a roller stand etc. ) Take extra care when starting the cut!9. 1 Cutting narrow workpieces (width less than 120 mm) (Fig. 11) Adjust the parallel stop (7) to the width of workpiece you require. Always use the push stick (3) in the area of the saw blade (4). (A push stick is supplied with the saw!) Always push the workpiece through to the end of the splitter (5). With short workpieces, use the push stick from the beginning. 9. 2 Cutting extremely narrow workpieces (width less than 30 mm) Adjust the parallel stop (7) to the width of workpiece you require. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]