User manual EINHELL BT-VC 1450 SA

[. . . ] Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:57 Uhr Seite 1 Operating Instructions Wet and Dry Vacuum Cleaner Art. -Nr. : 23. 423. 13 I. -Nr. : 01018 BT-VC 1450 SA Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:57 Uhr Seite 2 1 1 2 2 3 5 6 7 4 8 17 19 18 16 17 9 15 10 11 14 13 12 12 2 4 5 6 7 3 24 8 17 22 23 29 14 19 21 20 9 28 27 26 25 35 2 Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:57 Uhr Seite 3 4 1 12 5 13 30 34 33 32 31 31 33 6 13 30 31 7 30, 31, 13 10 33 33 8 33 9 13 30 13 33 3 Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:58 Uhr Seite 4 10 31 11 32 33 13 12 10 13 1 12 1. 1. 34 16 12 2. 34 2. 14 5 15 1. 18 2. 10 4 Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:58 Uhr Seite 5 16 17 24 25 18 35 5 Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:58 Uhr Seite 6 GB Important!When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. [. . . ] The appliance may only be connected to a shockproof socket. b b 5. 1 Assembling the appliance 5. 1 Appliance assembly Fitting the wheels (Fig. 4-11/13) Place a split pin for fitting the wheels (31) through the appropriate hole in the axle (33) and fit a washer (30) and a wheel (13) to the axle (33) (Fig. Now slide the axle (33) through the guides provided for it on the underside of the tank (10) (Fig. Fit the second wheel (13) to the empty end of the axle (33) and secure it with the other washer (30) and the split pin (31) (Fig. Push the covers (32) on to the outside of the wheels (13) so that the detents engage on the covers (32) for the wheel (13). 12/12) Fit the castors (12) into the appropriate mountings on the underside of the tank (10). Push the castors (12) firmly into the mounting until they engage with a clicking noise (Fig. 13/1) Place the handle (1) into the handle holders (16) and secure the handle with the supplied screws (34) as shown in figure 13. Anleitung_BT_VC_1450_SA_SPK7:_ 14. 10. 2008 7:58 Uhr Seite 8 GB Various attachments can be fitted to the combination nozzle depending on what you sort of work you wish to carry out: Wet vacuuming Use the attachment for wet vacuuming (Fig. Vacuuming smooth flooring Use the attachment for smooth floors (Fig. Vacuuming carpets Use the attachment for carpets (Fig. Fit the appropriate attachment into the combination nozzle (14) from underneath and secure it to the combination nozzle (14) using the side lugs (fig. Ensure that the attachments are perfectly secure. 3/23) The crevice nozzle (23) is designed for vacuuming solids and liquids in corners, edges and other areas that are difficult to access. The wet and dry vacuum cleaner is not suitable for the vacuuming of combustible liquids. For wet vacuuming, use only the supplied foam filter. 6. 4 Automatic mode Connect the power cable on your electric tool to the automatic socket-outlet (4) and connect the suction hose (9) to the extractor connector on your electric tool. Check that the connections are secure and airtight. You can use the supplied electric tool adaptor (22) to connect the suction hose (9) to the electric tool. To do so, fit it between the suction hose and the extractor port on the electric tool. Set the switch (7) on the wet and dry vacuum cleaner to position II, automatic mode. The moment you switch on the electric tool, the wet and dry vacuum cleaner switches on as well. When you switch off the electric tool, the wet and dry vacuum cleaner switches off as well after a pre-set delay. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]