User manual EIZO FLEXSCAN L360

[. . . ] E CONTENTS PRECAUTIONS __________________________ 4 INTRODUCTION ________________________ 10 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1 INSTALLATION ______________________ 16 1-1 Connecting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Position Adjustment This feature controls the screen position. The number of screen pixels and the screen position are fixed for the LCD monitor. Only one position is right and the displayed image should be adjusted to this position. 4. Resolution Adjustment This feature sets a suitable screen area corresponding to each display mode. Use this function for adjusting the screen to a suitable size when it is displayed smaller or larger than the actual screen size. Smaller than the actual screen images. Adjusted to actual screen size. Larger than the actual screen images. 2 USING THE SCREENMANAGER 39 14 preset timings have been committed to memory. In addition to these settings, a screen can be displayed correctly using the "Clock", "Phase" and "Position" adjustments if the input signal is one of the following resolutions (640 x 480, 720 x 400, 800 x 600, 832 x 624, 1024 x 768). If the signal is very different from one of the preset resolutions, then the screen can be adjusted using the "Resolution" Adjustment. The vertical resolution can be adjusted using the up and down buttons, and the horizontal resolution can be adjusted using the right and left buttons. When pushing the up or right buttons, the resolution is increased. When pushing the down or left buttons, the resolution is decreased. · The maximum resolution for the EIZO L360 LCD monitor is 1024 x 768. 5. Contrast Adjustment This feature controls the contrast of the screen. The contrast is changed by adjusting the gain level of the input signal to obtain the maximum contrast (0 ~ 63, 64 levels). OK Too high Too low Bright area is displayed too whitish. Adjustment procedure (Auto) (1)Push the Auto adjustment button on the front panel while displaying the "Contrast/Brightness" menu to automatically adjust the contrast. (2)The screen blanks for a moment, and adjusts the contrast to the maximum contrast level of the current input signal. (Manual) Adjust the contrast level using the right and left buttons until the percentage color is on the border of white and orange or fully orange. 40 2 USING THE SCREENMANAGER E * In the case of the percentage color flickering between orange and white, please note that this is not an error but actually the most optimum adjustment point. * The brightness of the entire screen is controlled by changing the "Brightness" controls. No contrast adjustment is required except when the graphics board or the resolution is changed from the previous one. 6. Brightness Adjustment This feature controls the brightness of the screen. The brightness of the entire screen is controlled by changing the brightness of the backlight. The black area on the screen is produced by shielding the backlight. Therefore, when changing the brightness of the backlight, the brightness of the black area on the screen will change very little. 2 USING THE SCREENMANAGER 41 2-3 Color Adjustment About Color Adjustments Entering the ScreenManager, select the "Color" icon and push the enter button to show the "Color" menu. The ScreenManager "Color" menu provides 3 color setting modes; 1, 2, and 3. You can also adjust the color settings for each mode and store them for future use. · Allow the monitor to warm-up for at least 20 minutes before making an adjustment. Color Mode There are 3 color modes. You can select from these color tones when using white background applications with Windows or Macintosh. [. . . ] (220-240 Vac) Only CE Marking Declaration of Conformity Kind of equipment: Type-designation: is in compliance with: Council Directive 73/23/EEC Council Directive 89/336/EEC Monitor L360 (Model No. FA-1563) EN60950:1992+A1+A2+A3+A4 EN55022 (classB):1995 EN50082-1:1992 EN61000-3-2:1995 EN61000-3-3:1995 Konformitätserklärung Geräteart : Gerätetyp : Monitor L360 (Modell-Nr. FA-1563) den folgenden Normen oder Vorschriften entspricht: EU-Richtlinie 73/23/EEC EU-Richtlinie 89/336/EEC EN60950:1992+A1+A2+A3+A4 EN55022 (classB):1995 EN50082-1:1992 EN61000-3-2:1995 EN61000-3-3:1995 Déclaration de conformité Nature de l'équipement : Type-désignation : est en conformité avec : Directive Européenne 73/23/EEC Directive Européenne 89/336/EEC EN60950:1992+A1+A2+A3+A4 EN55022 (classB):1995 EN50082-1:1992 EN61000-3-2:1995 EN61000-3-3:1995 Moniteur L360 (No. de modèle FA-1563) Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10. 80 (GS-VW-SG7/ 01. 97) mit dem Videosignal, 1024 Punkte x 768 Zeilen, RGB analog, 0, 7Vp-p und mindestens 75, 0 Hz Bildwiederholfrequenz, (non interlaced). [. . . ]