User manual EIZO FLEXSCAN L551

[. . . ] English SAFETY SYMBOLS This manual uses the safety symbols below. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates to ground for safety. Copyright© 2004-2005 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION. [. . . ] 18) before making the color adjustments. NOTE Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. (Allow the monitor to warm up for at least 20 minutes before making adjustments. ) Adjustment Contents Menu Color Mode Custom Temperature (p. 30) sRGB " ": Settable/Adjustable " ­ ": Fixed at the factory Function Descriptions Adjustable range ­ To set the color temperature Off / 6, 500K / 9, 300K Default setting is off (normal white) NOTE The values shown in the Kelvin are available only as a reference tool. Adjusting the <Gain> turns the <Temperature> adjustment "Off". 30) ­ To change each color (red, green and blue) 0 ~ 100% By adjusting the red, green and blue color tones for each mode, custom colors can be defined. Display a white or gray background image and adjust the <Gain>. NOTE The values shown in the percentage are available only as a reference tool. 30) invalidates the <Gain> adjustment. 20 4. Power-save Setup NOTE Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. This monitor complies with the "VESA DPMS" (p. 31) [Procedure] Set the PC's power saving settings. [Power saving system] PC Operation Power saving STAND-BY SUSPEND OFF Monitor Operation Power saving Power Indicator Green Orange Operate the mouse or keyboard to return to a normal screen. 4. ADJUSTMENT 21 English 5. ATTACHING AN ARM STAND The LCD monitor can be used with an optional arm stand. Using our optional arm or stand is recommended. (Ask your local dealer for information. ) NOTE If you will use the arm or stand of other manufacturers, confirm the followings to the manufacturers before selecting. ­ Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant) ­ Supportable Weight: Total weight of the monitor (without stand) and attaching equipment such as a cable ­ TÜV/GS approved arm or stand Please connect cables after attaching an arm stand. Setup Procedure 1. Hold the lower part of the stand cover and remove by lifting it up. Stand Cover 2. Remove the tilt stand by loosing the screws (4 pcs). 22 5. ATTACHING AN ARM STAND English 4. Attach an arm stand to the LCD monitor securely. Attach the removed stand cover again to the monitor. Arm-stand 4 Mounting Screws : M4 x 12 mm 5. ATTACHING AN ARM STAND 23 English 6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. No picture problems See No. 1 ~ No. 2 Imaging problems See No. 3 ~ No. 8 Other problems See No. 9 Problems 1. No picture Indicator status: Off Points to check with Possible Solutions Check that the power cord is correctly connected. [. . . ] Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device. - AC Cord - Shielded Signal Cable (enclosed) Canadian Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada. Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. [. . . ]