User manual EIZO FLEXSCAN L560T-CB

[. . . ] (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 Trade name: EIZO Model: FlexScan L560T-CB declare that the product is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] This function was created to reduce afterimage characteristics that are particular to LCD monitors when the monitor screen is left on for a long period without use. [Procedure] (1) Select <Off Timer> in the ScreenManager <Others> menu. (2) Select "Enable" and press the Right and Left Buttons to adjust the "On Period" (1 to 23 hours). [Off timer system] Timer On Period (1H - 23H) Last 15 min. in "On period" "On period" expired *1 Monitor Operation Advance Notice *1 Power off Blue Power Indicator Blue Flashing Flashing orange slowly Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor automatically enters the "Power Off" mode. Pressing the power button during the advanced notice period can reset "On Period" for another 90 minutes. It is possible to reset "On Period" as many times as needed. [Power Resumption Procedure] Press the power button to return a normal screen. 3. ScreenManager 19 English EIZO Logo display Enables to display the EIZO logo for a while when switching on the monitor (Default is no logo). If you desire to display or undisplay this logo, use this function. [To display] (1) Turn off the monitor's power by the Power button on the control panel. (2) Hold down the Enter button once again and turn the power back on. [To undisplay] (1) Turn off the monitor's power by the Power button. (2) Hold down the Enter button once again and turn the power back on. Automatically selecting the input signal function The monitor will automatically detect the inputted signal of either the connection for display. Connecting two PCs to the monitor When the one computer is switched off, the monitor will automatically dislay the other signal. Use the ScreenManager to switch the input selection to manual. [Procedure] (1) Select <Input Signal> in the <Others> menu. (2) Select "Manual". 20 3. ADJUSTMENT The monitor displays the digital input image correctly based on its pre-setting data. Screen Adjustment Screen adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first installing the display or whenever changing the system. Adjustment Procedure NOTE · Allow the LCD monitor to stabilize for at least 30 minutes before making image adjustments. 1. Press the Auto Adjustment Button on the control panel. The message "Your setting will be lost, if you press again now. " appears and remains on the screen for 5 seconds. While the message is on the screen, press the Auto Adjustment Button again to automatically adjust the clock, phase, and screen position. If you do not wish to do adjust the screen, do not press the Auto Adjustment Button again. [. . . ] If floors are covered with synthetic material, the relative humidity should be at least 30%. Electrical fast ±2kV ±2kV Mains power quality should be transient / burst for power supply lines for power supply lines that of a typical commercial or EN61000-4-4 ±1kV ±1kV hospital environment. for input/output lines for input/output lines Surge ±1kV line(s) to line(s) ±1kV line(s) to line(s) Mains power quality should be EN61000-4-5 ±2kV line(s) to earth ±2kV line(s) to earth that of a typical commercial or hospital environment. Voltage dips, short <5% UT (>95% dip in <5% UT (>95% dip in Mains power quality should be interruptions and UT) for 0. 5 cycle UT) for 0. 5 cycle that of a typical commercial or voltage variations on 40% UT (60% dip in 40% UT (60% dip in hospital environment. [. . . ]