User manual EIZO FLEXSCAN T68

[. . . ] English User's Manual ® F67/FX·D7 T68/TX·D7 Color Display Monitor CONTENTS PRECAUTIONS__________________________ 4 INTRODUCTION _________________________ 9 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 INSTALLATION ______________________ 10 1-1 Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The guidelines apply to PC systems and peripherals. AutoPower Function Once the monitor's main power has been switched ON, the monitor will start up automatically whenever the PC is turned on. If the PowerManager is set to VESA DPMS or NUTEK, the monitor will automatically power down (to PowerManager Mode 2) when the PC is turned off. If the PowerManager is set to OFF, however, the monitor power will remain on even after the PC is switched off. 32 2 SCREEN ADJUSTMENT 2-5 Other Settings E - Others menu - All of the icons shown in the ScreenManager "Others" menu are described below. Degaussing The monitor automatically degausses every time the power is turned ON and every time it is reactivated from the PowerManager power-saving Mode 2. A degaussing function is provided in the ScreenManager for use at other times. Note that the image vibrates slightly while degaussing is in progress, but will return to normal when degaussing is completed. · The degauss circuitry takes about 30 minutes to regain maximum power following degaussing before it can work again. "Degaussing" refers to the process of removing magnetic-field effects from the monitor. Operation of the monitor within a magnetic field may adversely effect color purity. Degaussing can be used to correct the problem. Input Priority This function is used to select which PC will have priority to control the monitor when utilizing two PCs. There are three settings available: "D-Sub", "BNC" or "Manual". The default priority setting is "D-Sub". The monitor constantly checks the input signals and switches automatically in accordance with the "Input Priority" settings (see chart on next page). Once a priority is set, whenever a change of signal is detected at the selected input, the monitor will switch the input to that signal. 2 SCREEN ADJUSTMENT 33 In the case of only one signal being present at either input, the monitor automatically detects and displays that signal. Priority setting D-Sub Performance If signals from both inputs are present, the monitor gives preference to D-Sub for the cases shown below: · When the power of the monitor is turned ON (see note 1). · When the signal input to D-Sub is changed even if active input was BNC. If signals from both inputs are present, the monitor gives preference to BNC for the cases shown below: · When the power of the monitor is turned ON (see note 1). · When the signal input to BNC is changed even if active input was D-Sub. The monitor will not detect signals automatically in this mode. Select the active input by pressing the input signal selection button on the monitor's front panel. BNC Manual 1 The Input Priority function does not automatically reactivate when the monitor has been in the power save mode. 2 The Input selection button on the front panel can be used to select either D-Sub or BNC as the active input at any time. Beep Use this feature to set the beeper ON or OFF. If the beeper is ON, the monitor will generate beep signals as shown below. If the beeper is OFF, the monitor will not beep. Short beep · ScreenManager item selected. [. . . ] MA-1990) EN60950:1992+A1+A2+A3 EN55022 (classB):1995 EN61000-3-2:1995 EN50082-1:1992 EN61000-3-3:1995 Konformitätserklärung Geräteart : Gerätetyp : Monitor F67 (Modell-Nr. MA-1990) den folgenden Normen oder Vorschriften entspricht: EU-Richtlinie 73/23/EEC EU-Richtlinie 89/336/EEC EN60950:1992+A1+A2+A3 EN55022 (classB):1995 EN61000-3-2:1995 Déclaration de conformité Nature de l'équipement : Type-désignation : est en conformité avec : Directive Européenne 73/23/EEC Directive Européenne 89/336/EEC EN60950:1992+A1+A2+A3 EN55022 (classB):1995 EN61000-3-2:1995 EN50082-1:1992 EN61000-3-3:1995 Moniteur F67 (No. de modèle MA-1990), FX·D7 (Modell-Nr. MA-1990) Hinweis zur Ergonomie : Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10. 80 durch die Ansteuerung mit der VGA - Videokarte, 1280 Punkte x 1024 Zeilen, RGB analog, 0, 7 Vp-p und mindestens 85, 0 Hz Bildwiederholfrequenz, non interlaced. [. . . ]