User manual ELECTRO-VOICE 1829T

[. . . ] A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrican for replacement of the obsolete outlet. [. . . ] 12 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Plasma Series Owner's Manual Thank you for choosing Electro-Voice® Plasma high powered loudspeaker systems. These systems are the culmination of EV's 75 years of experience in transducer design and over 50 years of experience in designing and building electronics. Please take time to consult this manual so that you can understand all the features built into your EV systems and fully utilize all their performance capabilities. ELECTRO-VOICE® Plasma Owners Manual 2 Safety First When setting up, installing and using Electro-Voice® Plasma speaker systems, there are a number of precautions that you should follow: · When Electro-Voice® Plasma speakers are used for portable applications in which they will be stacked directly on the floor, make sure that the floor or stage is solid and secure. Make sure to: · Route cables and position the stand so that performers, production crew and audience members will not trip over the stand or cables and pull the speaker system over. Secure cables with wire ties or tape whenever possible. · If you intend to hang or fly the Plasma two-way systems, only do so safely with the correct hardware and accessories. WARNING: Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of rigging objects overhead. Electro-Voice® strongly recommends that Plasma speakers be suspended taking into account all current national, federal, state and local regulations. It is the responsibility of the installer to ensure that Plasma speakers are safely installed in accordance with all such regulations. If Plasma speakers are suspended, Electro-Voice® strongly recommends that the system be inspected at least once a year. Turn on the power switch and ensure that the system is receiving power by monitoring the status LED. If the system is receiving signal, the LED will illuminate green. ELECTRO-VOICE® Plasma Owners Manual 4 1829T and P2 Amplifiers Input Signal Electronically balanced inputs for the connection of high-level signal sources such as mixers, signal processors, etc. Establishing the connection is possible via phone or XLR-type jacks. Balanced connection is recommended to prevent noise or HF-interference. Caution: Before connecting or disconnecting any plugs, make sure to set the level control to its counterclockwise stop, which prevents the system, the audience and yourself from being stressed by nasty contact noise. Input Loop Output is full bandwidth pass through. Crossover Mode Switch Selects between 40 Hz highpass filter for Fullrange use, and 100 Hz highpass filter for use with Plasma P2 subwoofer. It is not recommended that you use your 1829T in Fullrange with subwoofers. Level This control sets the output volume of the 1829T or P2 in a range between -dB and +6dB. The internal power amplifier provides a nominal input sensitivity of +6dBu. CAUTION: THIS APPLIANCE HAS NO USER-SERVICABLE PARTS INSIDE. LEAVE ANY SERVICING AND MAINTENANCE QUALIFIED SERVICE TECHNICIANS ONLY. 5 Level adjustment knob shown in place. Unit is shipped preset at 0 dB without knob installed (knob is shipped separately with your Plasma System). If knob is not used, please remember where you store it. [. . . ] Make sure that the AC cord is correctly connected if the switch is not lit upon turning the power on. If the AC cord is correctly connected and the AC switch does not light upon power-on, please contact your local dealer. AC Fuse During normal operation the AC fuse of the Plasma only blows at the occurrence of a malfunction. Exchanging the fuse is only permissible using a fuse of the same type (current, voltage and release characteristic). [. . . ]