User manual ELECTRO-VOICE ARISTOCRAT II DATASHEET

[. . . ] The velocity compensated port design overcomes the limitation of many small cabinet loudspeakers and enables exceptional low-frequency response without vent noise. SL8. 2 installation is incredibly simple with the included QuickSAMTM mounting system. The QuickSAMTM is a unique, integrated mounting bracket which is virtually foolproof. [. . . ] The QuickSAMTM is a unique, integrated mounting bracket which is virtually foolproof. It allows the installer to simply snap the speaker onto the bracket, then tighten it to the desired position. For array mounting, there is an optional array bracket kit available which allows multiple units to be mounted together for a variety of configurations. The horn features 100° x 100° coverage for broad even dispersion needed in many distributed audio applications. The SL8. 2 molded polymer enclosure is inherently water resistant. The addition of a multilayer grille with hydrophobic cloth and weatherized components enable the SL8. 2 to perform under many environmental conditions. An optional weatherized input panel cover with a gland nut is available for additional protection. The bracket shall allow for a quick snap fit mounting of the speaker enclosure for placement before securing. The speaker terminals shall include a 4 pin removable phoenix style connector to allow for signal pass through. The system shall be weather resistant to MIL Spec 810 and IEC 529 test conditions. The loudspeaker system shall meet the following performance criteria: Power handling, 200-Watts long term program using IEC268-5 shaped pink noise; Frequency response, 48 Hz ­ 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 92 dB at one watt, 60 Hz ­ 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum. The enclosure shall be 17. 75" (451mm) high, 11. 12" (282mm) wide, 10. 35" (263mm) deep. Net weight shall be 18. 5 lbs (8. 4 kg). CAUTION This SL8. 2 Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the ZX1 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. SL8. 2 Part Number · 301853-003 - SL8. 2, 100° x 100° Horn, Black Finish Performance Match · D170261 CPS2. 8, 120V Power Amplifier, 2 x 800W AB-ZX1i, Array Bracket Kit for 2 or 4 Systems, Black TC-ZX1i, Terminal Cover with Gland Nut Accessories · 301918-001 · 301955-001 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www. electrovoice. com © Telex Communications, Inc. [. . . ] The enclosure shall be 17. 75" (451mm) high, 11. 12" (282mm) wide, 10. 35" (263mm) deep. Net weight shall be 18. 5 lbs (8. 4 kg). CAUTION This SL8. 2 Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the ZX1 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. SL8. 2 Part Number · 301853-003 - SL8. 2, 100° x 100° Horn, Black Finish Performance Match · D170261 CPS2. 8, 120V Power Amplifier, 2 x 800W AB-ZX1i, Array Bracket Kit for 2 or 4 Systems, Black TC-ZX1i, Terminal Cover with Gland Nut Accessories · 301918-001 · 301955-001 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www. electrovoice. com © Telex Communications, Inc. [. . . ]