User manual ELECTRO-VOICE CO85A

[. . . ] Any hardware used to suspend a Phoenix speaker that is not associated with Electro-Voice® is the responsibility of others. Ground Stack: When using multiple Electro-Voice® Phoenix speakers in a ground stack configuration, the feet of each enclosure is designed to fit into grooves of the enclosure below it. This is both for the safety of the ground stack and serves as an alignment for properly arraying multiple loudspeakers. Always check that the feet are resting in the grooves when using multiple speakers (Figure 1). [. . . ] Always check that the feet are resting in the grooves when using multiple speakers (Figure 1). Unless you can safely lift the weight of the loudspeaker on to the ground stack, have another person to help you place it. The ground stack should be placed on a solid, level surface. When using subs on a surface that is hard or slick, use a piece of carpet or other material between the feet and supporting surface to prevent the subs (and stacks) from "walking". When using a ground stack in windy outdoor conditions, when the surface is slippery, or when in adverse conditions, Electro-Voice® recommends using a ratchet strap to secure the speakers. For a complete list of the configurations possible with an Electro-Voice® Phoenix system, please consult the Application Guide at www. electrovoice. com. Foot on Bottom of Second Enclosure Groove on Top of First Enclosure Figure 1: Groundstacking Configuration Stand Mount: The Electro-Voice® PX1122M and PX1152M include 1-3/8" stand mounts for use with tripod stands. Check the specifications of the speaker stand to be certain it is capable of supporting the weight of the speaker. Place the speaker stand on a flat, stable surface and be sure to fully extend the legs of the stand. The yellow wire corresponds to the positive terminal, and the yellow and black wire corresponds to the negative terminal. Reattach the horn to the enclosure using the (12) screws. Reattach the grille using the (6) screws (reverse of Figure 2). Grille Screw (x6) PX2122 or PX2152 Loudspeaker (PX2152 Shown) Horn Screw (x12) Loudspeaker Grille Horn/ High-Frequency Subassembly Figure 3: Removing the Horn from the Enclosure Manifold/ Compression Driver Assembly Manifold Bolt (x4) Manifold Nut (x4) Horn Figure 2: Removing the Grille from the Enclosure Figure 4: Detaching the Manifold Assy from the Horn Technical Specifications: PX1122M PX1152M PX2122 PX2152 PX2181 Freq. Hipass Frequency: Axial Sensitivity1: Max Calculated SPL1: Horizontal Coverage: Vertical Coverage: Power Handling (Passive): LF Power Handling (Biamp): HF Power Handling (Biamp): LF Transducer: HF Transducers: Crossover Frequency: Impedance (Passive): LF Impedance (Biamp): HF Impedance (Biamp): Connectors: Enclosure Material: Suspension: Grille: Dim (H x W x D): Net Weight: Shipping Weight: Recommended Amplifier: Accessories: 1 70 Hz - 15 kHz 55 Hz - 19 kHz 50 Hz 98 dB (1W/1m) 132 dB 90° 45° TBA TBA TBA TBA TBA 90 Hz - 11 kHz 70 Hz - 18 kHz 80 Hz 102 dB (1W/1m) 138 dB 30°, or 45° 45°, or 30° N/A 60 Hz - 11 kHz 50 Hz - 18 kHz 40 Hz 101 dB (1W/1m) 60°, or 45° 45°, or 60° 1200W Continuous, 4800W Peak 1000W Continuous, 4000W Peak 45 Hz - 160 Hz 40 Hz - 180 Hz 35 Hz 105 dB (1W/1m) 141 dB Omnidirectional Omnidirectional N/A 600W Continuous, 2400W Peak 500W Continuous, 2000W Peak 80W Continuous, 320W Peak (1) DVX3121, 12 in. (305 mm) Driver 1400 Hz 8 Ohms Nominal 8 Ohms Nominal 8 Ohms Nominal (3) Neutrik Speakon NL4's Rigging Point for PX-SAM Strong-Arm Accessory 546mm x 366mm x 305mm (21. 50" x 14. 42" x 12. 04") 23. 1 kg (51 lbs) 25. 2 kg (56 lbs) Electro-Voice® CP3000S PX-SAM Strong-Arm Kit (2) Neutrik Speakon NL4's 18mm Plywood with Black EVCoatTM (8) M10 Points - (6) on Top and (2) on Bottom of Enclosure 1219mm x 457mm x 445mm (48. 00" x 18. 00" x 17. 50") 50. 9 kg (112 lbs) 53. 1 kg (117 lbs) 45. 6 kg (100. 5 lbs) 47. 9 kg (105. 5 lbs) Electro-Voice® CP4000S PX-D1 Dolly Kit PX-G1 Phoenix Grid EBK-M10 Eyebolt Kit TBA (2) DVX3121, 12 in. (305 mm) Driver 1600 Hz N/A (2) DVX3150, 15 in. (381 mm) Driver 1900Hz 4 Ohms Nominal 4 Ohms Nominal N/A (2) DVX3180, 18 in. [. . . ] (305 mm) Driver 1400 Hz 8 Ohms Nominal 8 Ohms Nominal 8 Ohms Nominal (3) Neutrik Speakon NL4's Rigging Point for PX-SAM Strong-Arm Accessory 546mm x 366mm x 305mm (21. 50" x 14. 42" x 12. 04") 23. 1 kg (51 lbs) 25. 2 kg (56 lbs) Electro-Voice® CP3000S PX-SAM Strong-Arm Kit (2) Neutrik Speakon NL4's 18mm Plywood with Black EVCoatTM (8) M10 Points - (6) on Top and (2) on Bottom of Enclosure 1219mm x 457mm x 445mm (48. 00" x 18. 00" x 17. 50") 50. 9 kg (112 lbs) 53. 1 kg (117 lbs) 45. 6 kg (100. 5 lbs) 47. 9 kg (105. 5 lbs) Electro-Voice® CP4000S PX-D1 Dolly Kit PX-G1 Phoenix Grid EBK-M10 Eyebolt Kit TBA (2) DVX3121, 12 in. (305 mm) Driver 1600 Hz N/A (2) DVX3150, 15 in. (381 mm) Driver 1900Hz 4 Ohms Nominal 4 Ohms Nominal N/A (2) DVX3180, 18 in. [. . . ]