User manual ELECTRO-VOICE DC30T

[. . . ] This includes that the operation location provided sufficient ventilation and the device is not exposed to direct sunlight or the direct radiation or reflection from any heat source. Installing the loudspeaker systems choose a location that gets not affected by extreme and / or constant vibration or other mechanical oscillation. also make sure that the speakers are installed at locations that are free from dust and / or moisture. CAUTION We strongly recommend that you leave the connection of the appliance to the qualified and experienced service technician who is specialized in connecting electrical and electronically equipment. Do not take the risk of Electro-shock or shock hazard. [. . . ] Turning a control clockwise increases the volume of the corresponding source. We recommend to leave the controls of momentarily not used inputs their minimal setting "0". The control lets you individually set the volume of the sound output that are connected to the "MONITOR OUTPUT" (4) and "1W/8 "(25). Turning controls clockwise increase the volume of the corresponding source. The Limited Warranty does not apply to:(a) exterior finish or appearance; (b) certain specific items described in the individual product-line statements below, or in the individual product sheet or owner's manual; (c) malfunction resulting from use or operation of the product other than as specified in the product data sheet or owner's manual;(d) malfunction resulting from misuse or abuse of the product; or (e) malfunction occurring at any time after repairs have been made to the product by anyone other than Electro-Voice Service or any of its authorized representatives. Obtaining Warranty Service To obtain warranty service, a customer must deliver the product to Electro-Voice Service or to any of its authorized service representatives, together with proof of purchase of the product in the form of a bill of sale or receipted invoice. A list of authorized service representatives is available from Elector-Voice Service at 12000 Portland Avenue. Music signal monitor output level control Incidental and Consequential Damages Excluded 4. "MONITOR OUTPUT" This allows signal output of the "AUX1", "AUX2", "CASSETTE" and "TUNER" input mixing. It can be used to control an audio appliance with input impedance over 600 ohms (e. g. Earphone or an additional amplifier etc. ) The output signal is controlled only by the volume controls of the "AUX 1", "AUX 2", "TUNER" and music signal level control (3). This function is toggle switch the "1W/8 " (25) additional loudspeaker. Product repair or replacement and return to the customer are the only remedies provided to the customer. Electro-Voice shall not be liable for any incidental or consequential damages including, without limitation, injury to persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The fuse can only be changed, in the event of a fault or changing the supply voltage, by an EV service center. d AC 115V~ 60Hz DC 24V 15A RATED INPUT 315W LINE 115V~ 60Hz DC 24V 15A Mains 24V of No DC POWER LINE OUTPUT 1 2 ON OFF 3 + INPUT10 1234 - 1W / 8W + Priority Tel. paging 1 master volume control 1 treble control 1 bass control 230 Vac ( 5%)-50Hz / 145W (MA-1206 series) 230 Vac( 5%)-50Hz / 315W (MA-1212 series) 5A (MA-1206 series) 10A (MA-1212 series) 480 320 150 mm (18. 9" 12. 6" 9kg (19. 84 Ib) (MA-1206 series) 12kg (24. 46 Ib) (MA-1212 series) 5. 9") DC24V 10A + - COM 4W 25V 70V 100V Output power capacity Nominal power capacity with supply at 24Vdc Frequency response Total harmonic distortion - + 4 ohm Signal / noise ratio Inputs / sensitivity-impedance Connecting the speakers to 4 ohm output DC24V 10A + - Outputs for speakers / Ohms Outputs for speakers / Volts COM 4W 25V 70V 100V Additional outputs / voltage-impedance Tone controls 0 25V 0 25V 0 25V Controls Power supply / Consumption Connecting the speakers to 25V output Direct current draw (24V) Dimensions(L Weight H W) DC24V 10A + - COM 4W 25V 70V 100V 0 70V 0 70V 0 70V Connecting the speakers to 70V output 5 10 Read these instructions. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two lades and a third ground prong. The third prong are provided for your safety. When the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenient receptacles, and the point where they exit from thee apparatus. Only use attachments/accessories specified by the manufacturer. The apparatus should be placed on a solid surface with a minimum distance of 1 m from the back or side plate to the wall and not in the following environments of cases; moist place; under direct radiation sunlight or other strong heat radiation. [. . . ] "INPUT 1 ~ INPUT 10" Inputs These ten balanced/unbalanced combination type jack (XLR and 6. 3mm) input, Meant for the connection of-condenser type microphone that accept 24V phantom power, dynamic microphone (30-600ohms) or a high level sound source (e. g AM/FM tuner, cassette desk, CD player, ect. ) In case you are using , it is necessary to use the switch (20). 20. Input sensitivity switch (AUX1 , AUX2) By turning switch onto the "1" position, the "AUX 1" , "AUX 2" input suitable for connected to CD player signal output. By turning this switch onto the "2" position, the "AUX1", "AUX2" input suitable for connected to AM/FM radio signal output. By turning this switch onto the"3" position, the "AUX1" "AUX2" input suitable for connected to desktop cassette player signal output. [. . . ]