User manual ELECTRO-VOICE X-LINE PRODUCTS BROCHURE

[. . . ] The companion Xsub subwoofer systems would either be stacked on the ground underneath the Xvls/Xvlt full-range column or would be hung in a separate column suspended next to the full-range column. Each column of loudspeakers is then suspended from a grid which is in turn secured to the building structure (usually via a motorized hoist). The external X-Line rigging hardware consists of hinge assembles at the rear and chain strap assemblies at the front. [. . . ] This hardware will work for linking Xvls or Xvlt enclosures. Attaching the Downfill at the Bottom: The third set of rigging is used to attach the Xfil1 or Xfil 2 to the bottom of the column of loudpeakers. As before, there are two pieces of rear rigging hardware and two pieces of front rigging hardware required for this purpose. The front hardware consists of two Xvsd chain strap assemblies. The rear hardware consisits of two Xvhl linking hinge assemblies. This hardware will work for attaching the Xfil1 or Xfil2 to either the Xvls or Xvlt enclosures. (Note that the Xvhl linking hinge is the same hardware used to link Xvls or Xvlt systems together; however, the Xvsd chain strap at the front is different. ) The Xvhg, Xvhl, Xvsg, Xvsl and Xvsd rigging assemblies are all manufactured and sold by EV/Telex. EV/Telex does not manufacture or sell grids; however, the EV/Telex engineers have worked with ATM Flyware (a third-party company which specializes in rigging hardware for the professional loudspeaker industry) to develop a grid for the X-Line loudspeakers that ATM will sell direct to our customers. X-LineTM Loudspeaker & Rigging Packages Special loudspeaker/rigging sales packages have been created that include one flying Xvls, Xvlt, Xfil1, Xfil2 or Xsub loudspeaker and all external rigging required to link two boxes together. For the flying Xvls, Xvlt and Xsub, that includes one loudspeaker, two Xvsl front chain assemblies and two Xvhl rear hinge assemblies. For the Xfil1 and Xfil2, that includes one loudspeaker, two Xvsd front chain assemblies and two Xvhl rear hinge assemblies. All orders for customers should be placed for these packages and not for the individual loudspeakers without rigging. The customers should be reminded that these rigging packages only include the linking rigging hardware and not the hardware required to attach to the grid. Therefore, the customers should be reminded that they additionally need to place orders for that grid hardware (two Xvsg front chain assemblies per column of loudspeakers and either two Xvhg flexible chain rear hinge assemblies or two Xvhl solidarm rear hinge assemblies per column of loudspeakers). Furthermore, because rigging can be misplaced or lost in the field, customers should be encouraged to place orders for a few pieces of spare rigging (Xvhl, Xvhg, Xvsl, Xvsd and Xvsg). Pro Audio Group · Telex Communications Inc. [. . . ] The recommended power amplifiers are the Electro-Voice P3000, which are available through the normal EV/Telex distribution. Pro Audio Group · Telex Communications Inc. · 12000 Portland Ave South · Burnsville, MN 55337 USA · Tel: 952-884-4051 · Fax: 952-887-9212 www. electrovoice. com X-LineTM Loudspeaker Specifications Xvls FULL RANGE LINE ARRAY LOUDSPEAKER SYSTEM Configuration: 3-Way Active Crossover Frequencies: 220Hz & 1250 Hz Nominal Coverage Pattern: 90H x 5. 0V HF Section: Drivers - Three ND5-16 16-ohm Compression Drivers Horn - 90H x 5. 0V Long-Term Power Rating - 225 watts total (75 watts each) Nominal Impedance - One 5. 3-ohm load MB Section: Drivers - Two ND08 16-ohm Midbass Drivers Horn - 90H x 5. 0V Long-Term Power Handling - 600 watts total (300 watts each) Nominal Impedance - One 8-ohm Load LF Section: Drivers - Two EVX155Plt 8-ohm Woofers Drivers Long-Term Power Handling - 1200 watts total (600 watts each) Nominal Impedance - Two 8-ohm Loads Wiring Configuration: Two Paralleled 8-Pin Neutrik NL8 Connectors Pins 4: HF (5. 33 ohms, 225 watts) Pins 3: MB (8. 00 ohms, 600 watts) Pins 2: LF2 (8. 00 ohms, 600 watts) Pins 1: LF1 (8. 00 ohms, 600 watts) System Weight: 257 lbs Enclosure Dimensions: 49. 000 in. deep Enclosure Shape: Rectangular Rigging: Proprietary Hinge on Back, Proprietary Adjustable Chain on Front Xvlt FULL-RANGE LINE ARRAY LOUDSPEAKER SYSTEM Configuration: 3-Way Active Crossover Frequencies: 220Hz & 1250 Hz Nominal Coverage Pattern: 120H x 8. 5V HF Section: Drivers - Three ND5-16 16-ohm Compression Drivers Horn - 120H x 8. 5V Long-Term Power Rating - 225 watts total (75 watts each) Nominal Impedance - One 5. 3-ohm load MB Section: Drivers - Two ND08 16-ohm Midbass Drivers Horn - 120H x 8. 5V Long-Term Power Handling - 600 watts total (300 watts each) Nominal Impedance - One 8-ohm Load LF Section: Drivers - Two EVX155Plt 8-ohm Woofers Drivers Long-Term Power Handling - 1200 watts total (600 watts each) Nominal Impedance - Two 8-ohm Loads Wiring Configuration: Two Paralleled 8-Pin Neutrik NL8 Connectors Pins 4: HF (5. 33 ohms, 225 watts) Pins 3: MB (8. 00 ohms, 600 watts) Pins 2: LF2 (8. 00 ohms, 600 watts) Pins 1: LF1 (8. 00 ohms, 600 watts) System Weight: 253 lbs Enclosure Dimensions: 49. 000 in. [. . . ]