User manual ELECTRO-VOICE XI-2122MHA EDS

[. . . ] Xi-2122MHA/42F Dual 12-Inch Two-Way, Long-Throw, Mid-High 40° x 20° Sound Reinforcement System Key Features: · · · Unprecedented Output in a High-Level, TwoWay Design Dual ND12A 12" Neodymium Mid-Bass Drivers Coaxially-Mounted Dual ND6-16 3" Diaphragm HF Compression Driver for Very High Output Far-Field, Long-Throw 40° x 20° Coverage Pattern Ring-Mode Decoupling / RMDTM Built-In L-Track Rigging Available in Black or White Footprint Identical to Xi-1153A, Xi-1183A, Xi-2153A, Xi-1191A, and Xi-2181A · · · · · General Description: The Electro-Voice Xi-2122MHA/42F loudspeaker system was designed for optimal performance in both concert-sound and permanent-installation applications where studiomonitor sound quality is required at concert-sound levels. [. . . ] The Electro-Voice P3000 amplifier is recommended for powering the Xi-2122MHA/42F. ® Technical Specifications: Freq. Response1 (-3 dB): 170 Hz - 16 kHz Freq. Range1 (-10 dB): 125 Hz - 20 kHz Max Calculated SPL2: 145 dB Coverage: 40° x 20° MB Power Handling: 600W Continuous, 2400W Peak HF Power Handling: 150W Continuous, 600W Peak MB Sensitivity: 112 dB, 1W/1m HF Sensitivity: 116 dB, 1W/1m MB Impedance: 4 ohms (Nominal) HF Impedance: 8 ohms (Nominal) MB Transducer : (2) ND12A 12" (305mm) Drivers, 8 ohms HF Transducer : (2) ND6-16 3" (76mm) Diaphragm Comp. Drivers, 16 ohms Crossover Frequency3: Use Recommended Parameters Connectors: Two Neutrik Speakon® NL8MPR Paralleled Enclosure Material: 13-ply Birch plywood Grille: 16 GA steel Dim (H x W x D): 914 x 586 x 759 mm (36. 0" x 23. 1" x 29. 9") Net Weight: 86. 3 kg (190 lbs) Shipping Weight: 90. 1 kg (199 lbs) 1 2 3 Full Space measurement with a Dx38 Controller Max Calculated SPL of MB Section Download at www. electrovoice. com Xi-2122MHA/42F Full Range Loudspeaker Frequency Response (Full & Half Space): Impedance: Beamwidth: Horizontal Off Axis Frequency Response: Directivity: Vertical Off Axis Frequency Response (Up or Down): Wiring Diagram: Engineering Data Sheet Horizontal 1/3 Octave Polars: Vertical 1/3 Octave Polars: Dimension Drawings: Wiring/Connection Chart: CAUTION This Xi Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the X-Array Xi Install Flying Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Performance Match Xi-2122MHA/64F Part Numbers · · 1125-3442 - Black 1125-3445 - White Architectural & Engineering Specs: · P3000 (RL) · CPS 2. 8 · Dx38 · P1200 (RL) · CPS 2. 11 The loudspeaker system shall be a two-way bi-amp system. The system shall have dual 12-inch, fully horn-loaded mid-bass drivers with 2. 5-inch voice coils and a nominal impedance of 4 ohms. The mid-bass drivers shall have a power-handling capacity of 600 watts for 8 hours (as per ANSI/EIA RS-426 A & AES 2-1984). The high-frequency section shall be coaxially mounted in the midbass horn and shall employ dual compression drivers capable of handling 300 watts, 1, 760- to 20, 000-Hz when pink noise of a 6dB crest factor is applied for 2 hours (as per AES 2-1984 and ANSI S4. 26-1984 standards). [. . . ] For customer orders, contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 736-4212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. [. . . ]