Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELK PRODUCTS ELK-SWB28. We hope that this ELK PRODUCTS ELK-SWB28 user guide will be useful to you.
Lastmanuals help download the user guide ELK PRODUCTS ELK-SWB28.
Manual abstract: user guide ELK PRODUCTS ELK-SWB28
Detailed instructions for use are in the User's Guide.
[. . . ] ELK
NEW Hinged Lid!
ELK-SWB28
28" STRUCTURED WIRING BOX
PRODUCTS, INC.
INSTALLATION
The ELK-SWB28 box may be flush or surface mounted. Flush mounting is ideal for hollow frame walls with studs on 16" centers. [. . . ] Adjust the box edge 1" from the stud face and tighten screws. Then install screws in the lower 2 slots.
1"
C) If desired, install an electrical outlet in the rectangular knockout on the lower flange. A standard one gang electrical "J" box is mounted using #6 Flat Head Self-Tapping Screws (not included) D) Pull wires through one or more of the entry holes. The design of the SWB28 allows wires to be organized along the sides. Plastic wire ties can be used to secure wiring as shown.
Tie Wrap
INSTALLING THE LID AFTER WALLBOARD INSTALLATION AND/OR PAINTING
E) To install the lid, start two (2) 6-32 x 3/8" type F sheet metal screws into the top and bottom holes of the hinge as shown below. F) Hold lid against the left side of the box and align the two 6-32 screw heads (from step E) with the slotted (key) holes on the box. Move lid to right until the screws engage the slots, then lower into place. BOX MAY BE ADJUSTED FORWARD AND BACK AS NEEDED. Tighten the first 2 screws, then install the remaining 4 screws. Door should open and close freely.
PRINTED IN USA
ELK PRODUCTS, INC. [. . . ] Circuit Board ELK-MM-447 NX-8 NX-4 NX-540 ELK-ML8 NX-580 NX-408 Glide 1 Holes 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 Top Glide 2 Holes 15, 16 17, 18 12, 14 8, 9 6, 7 6, 7 4, 5 Board Length 9-3/16" 11" 8" 6" 4" 4" 4-11/16"
21 22
23 24 25 26 27 28
I) If desired, two (2) #10 sheet metal screws can be installed in the right side of the lid (upper and lower) to make the box more secure against tamper. In addition, the SWB28 provides mounting holes for two tamper switches.
Optional Accessories For SWB28
ELK-SWD1 1. 75" Gromment Donuts (2) ELK-SWG Circuit Board Glides (2) ELK-SWNS1 Nylon Standoffs for SWP (10) ELK-SWP 4. 5" Multipurpose Adapter Plate ELK-SWP3 3" Multipurpose Adapter Plate ELK-SWS Battery Shelf [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELK PRODUCTS ELK-SWB28
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ELK PRODUCTS ELK-SWB28 will begin.
