User manual EMERSON FANS 60 DESIGNER

[. . . ] BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 1 READ AND SAVE THESE INSTRUCTIONS 60" DESIGNER Ceiling Fan Owner's Manual CF760AB00 CF760AW00 CF760WW00 Net Weight: 30. 0 Lbs. Model No. CF760BS00 CF760ORB00 ! CF760PW00 CF760WB00 WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner's manual carefully and keep it for future reference. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. [. . . ] ! seat properly on the motor hub, loosen the adjacent flange screws, reengage and reseat the flanges, then tighten the screws again. WARNING BLADE ASSEMBLY To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. BLADE FLANGE SCREWS 11. The blade flanges have an interlocking feature that must be fully engaged before tightening the screw. Make sure all the flanges are properly engaged and then tighten the flange screws. If one of the flanges does not Figure 8 12. You have now completed the assembly of your new ceiling fan. You can now proceed with hanging and wiring your fan. Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. ! WARNING WARNING Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked "Acceptable for Fan Support", and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. ! WARNING To avoid fire or shock, follow all wiring instructions carefully. Noise and fan damage could result. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation). Securely connect wires with wire connectors supplied. BLACK AND BLUE GROUND FAN WIRES WIRE LISTED WIRE CONNECTOR (3) WHITE SUPPLY (NEUTRAL) 3. Screw the two threaded studs (supplied) into the tapped holes in the hanger bracket. Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 13). Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs (supplied). Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan switch. CEILING COVER THREADED STUD (2) GREEN WIRE (GROUND) FROM HANGER BRACKET GREEN WIRE (GROUND) FROM HANGER BALL WHITE FAN WIRE BLACK SUPPLY (HOT) KNURLED KNOBS (2) LOCKWASHER Figure 13 Figure 12 NOTE: CEILING COVER OMITTED FOR CLARITY. ! WARNING NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner's Manual for wiring. To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. 2. Securely connect the fan motor white wire to the supply white (neutral) wire 6. [. . . ] All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR. Do To Correct Problems: Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. [. . . ]