User manual EMERSON FANS APOLLO

[. . . ] READ AND SAVE THESE INSTRUCTIONS AMERICA'S FAN COMPANY 52" "APOLLO" Series Model No. CF3900WW01 CF3900PB01 CF3900HTW01 CF3900TG01 CF3900AW01 CF3900WPB01 CF3900BS01 CF3900CK01 Net Weight: CF3900AB01 CF3900OB01 CF3900BQ01 18. 0 Lbs. ® "APOLLO" Series Ceiling Fan Owner's Manual Part No. BP7234-3 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for the lifetime from the date you purchased your ceiling fan. [. . . ] The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed. ! 5. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 8. PIN HANGER BALL DOWNROD SETSCREW WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. 6. Screw two 1" threaded studs (provided) into the motor. Leave approximately 7/8" of the stud extending above motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two knurled knobs (supplied) to secure the cover. NOTE: Make sure the red and brown leads are capped with wire connectors and are completely inside motor cover and not pinched between the motor cover and motor. KNURLED KNOB MOTOR COVER WIRE CONNECTORS HANGER BALL DOWNROD HAIRPIN CLIP MOTOR COUPLING RED LEAD BROWN LEAD 7/8" 1" THREADED STUD MOTOR SETSCREW CLEVIS PIN HAIRPIN CLIP HANGER BALL/ DOWNROD ASSEMBLY CLEVIS PIN CLEVIS PIN MOTOR COUPLING 7. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top. 8. Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod. Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! WARNING 4. Install the setscrew (supplied in loose parts bag) in the motor coupling. While pulling up on the hanger ball, tighten the setscrew using the 5/32" setscrew wrench (supplied). NOTE: The setscrew must be properly installed as described above, or fan wobble could result. DOWNROD SETSCREW WRENCH It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Do not insert foreign objects between rotating fan blades. 8-32 x 3/8" FLAT HEAD MOUNTING SCREWS (3) 6 Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. ! ! WARNING WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. [. . . ] Check main and branch circuit fuses or circuit breakers. Check line wire connections to fan and switch wire connections in the switch housing. ! WARNING: Make sure main power is turned off. 3. Screws securing fan blade flanges to motor hub are loose. Switch housing binding against blade hub. [. . . ]