User manual EMERSON FANS CORNERSTONE

[. . . ] READ AND SAVE THESE INSTRUCTIONS 1895 TM ® TM Model No. CF1AB01 CF1WB01 CF1PW01 DATE CODE: The date code of this fan may be found on the box, stamped in ink on a white label. You should record this data above and keep it in a safe place for future use. Max. With Blades ® CORNERSTONETM Series Ceiling Fan Owner's Manual Part No. BP7250-2 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. [. . . ] Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. 14° FOUR-BLADE FLANGE 10-32 x 5/8" OVAL HEAD SCREWS (2 PER BLADE FLANGE) Figure 8 MOTOR HUB 14. Attach one blade assembly to the motor hub using four 10-32 x 5/8" oval head screws (supplied) (Figure 9). Install the other blade assembly in the same manner. Gently snug all flange screws to the motor hub. Make sure the ends of the flanges are engaged, then securely tighten all flange screws, working in a clockwise sequence. PIN HANGER BALL DOWNROD 20° TWO-BLADE FLANGE Figure 6 10. The fan comes with blue, black and white leads that are 80" long. Before installing fan, measure up approximately 6 to 9-inches above the ball/ downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads. Use five 10-32 x 3/8" pan head screws and flat washers (supplied) to secure the flange to the blade (Figure 7). Repeat for the remaining blade(s). 10-32 x 3/8" PAN HEAD SCREW (5) FLAT WASHER (5) BLADE 10-32 x 5/8" OVAL HEAD SCREWS (4 PER BLADE FLANGE) Figure 9 ! MOTOR HUB WARNING To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades. BLADE FLANGE 15. Turn fan assembly over so the bottom is oriented up. Partially install two 8-32 x 1/2" screws (supplied) in the switch housing assembly (Figure 10). Slip the speed control switch chain through the hole in the upper cover trim, then position the cover trim on the switch housing assembly so that the two screws protrude through the key hole slots in the cover trim. Turn the cover trim fully clockwise and then securely tighten the two 8-32 x 1/2" screws. Consult a qualified electrician if in doubt. TWO SCREWS SUPPLIED WITH OUTLET BOX HANGER BRACKET TAB Figure 13 Figure 2 If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. ! WARNING 2. Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 14). Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 13). ! Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with national and local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. 6 NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. OUTLET BOX HANGER BRACKET Figure 143 Figure ! HANGER BALL/ DOWNROD ASSEMBLY 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 15). [. . . ] All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR. What Will Emerson Company Do To Correct Problems: Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. [. . . ]