User manual EMERSON FANS HF1160

[. . . ] You can return the product to our factory or to your nearest authorized service center. · To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson Company, 8100 W. Include all model numbers shown on the product with your request. · To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center. [. . . ] WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Company. Substitution of parts or accessories not designated for use with this product by Emerson Company could result in personal injury or property damage. WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. DATE CODE: The date code of this fan may be found on the box, stamped in ink on a white label. You should record this data above and keep it in a safe place for future use. 2 Checking Contents of Package 1. Unpack the items carefully to avoid damage to any of the components. Check to see that you have received the following parts: NOTE: If you are uncertain of part description, refer to the exploded view illustration. Seven M6-1. 0 x 12mm Phillips hex head screws 5. Two M4 -. 7 x 10mm pan head knurled screws 8. One setscrew wrench NOTE: Intermixing blades between fans can cause excessive wobble. Keep blades in original sets of three. Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. ! WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked "Acceptable for Fan Support of 50 lbs. or less", and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. ! WARNING Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. Assembly Instructions CAUTION: The blade assemblies must be mounted on the motor assembly so that the "This Side Up" label is visible at the top of the motor (Figure 1). Install one blade assembly on the top of the motor assembly using two M6-1. 0 x 12mm Phillips hex head screws, two split lockwashers and two flat washers (supplied) (Figure 1). Repeat this procedure for the remaining two blade assemblies. ! WARNING Do not install or use fan if any part is damaged or missing. Call Toll-Free: 1-800-654-3545 ! WARNING M6-1. 0 x 12mm PHILLIPS HEX HEAD SCREW SPLIT LOCKWASHER FLAT WASHER BLADE ASSEMBLY LABEL MOTOR YOKE SETSCREW (2) This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Company. Substitution of parts or accessories not designated for use with this product by Emerson Company could result in personal injury or property damage. MOTOR ASSEMBLY 3 Figure 1 2. Using the setscrew wrench (supplied), remove the two setscrews from the top of the motor yoke (Figure 1). [. . . ] If a remote speed control is to be used, refer to the Owner's Manual included with the control for proper installation and wiring. After completing the installation, restore the power and test run the fan. NOTE: When any solid state motor speed control is used, a humming noise may be present in the fan on low speed. This hum in no way affects the operation of the fan and is acceptable in most industrial installations. This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Company. [. . . ]