User manual EMERSON FANS ODYSSEY

[. . . ] READ AND SAVE THESE INSTRUCTIONS Model No. CF2454WW02 CF2454BS02 CF2454PW02 CF2454BQ02 Net Weight: 26. 0 Lbs. ® THE ODYSSEY Series Ceiling Fan Owner's Manual Part No. BP7211-8 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner's manual carefully and keep it for future reference 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. [. . . ] Strip insulation 1/2" from end of the wires. Using the wire connector supplied, connect the uplight yellow lead assembly to the yellow lead from the fan motor and housing assembly. 4" UPLIGHT YELLOW LEAD ASSEMBLY CUT HERE HANGER BRACKET SW375 RECEIVER OPEN SIDE HANGER BALL DOWNROD 3" Figure 19 FLAT SIDE CEILING COVER Figure 17 7. Route the white, blue, and black motor leads through the downrod. Fold the yellow wire into the slot in the motor coupling, slide the downrod down the wires and seat the downrod in the motor coupling (Figure 20). Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 20). The clevis pin must go through the holes in the motor coupling and the holes in the downrod . Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed. 8 ! WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. NOTE: Make sure the red and brown leads are capped with wire connectors. Make sure red, brown, and yellow wire connectors are completely inside motor coupling cover and not pinched between the motor coupling cover and motor. KNURLED KNOB MOTOR COUPLING COVER WIRE CONNECTOR YELLOW LEADS 1-1/4" THREADED STUD 7/8" YELLOW LEADS TO BE POSITIONED IN SLOT IN MOTOR COUPLING SETSCREW WIRE CONNECTORS DOWNROD HAIRPIN CLIP MOTOR COUPLING RED LEAD BROWN LEAD MOTOR BRACKET CLEVIS PIN Figure 22 11. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 23). Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod (Figure 23). Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! DOWNROD HAIRPIN CLIP CLEVIS PIN CLEVIS PIN MOTOR COUPLING Figure 20 9. Install the setscrew (supplied in loose parts bag) in the motor coupling and tighten using the 5/32" setscrew wrench (supplied) (Figure 21). WARNING It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. DOWNROD PIN HANGER BALL SETSCREW CEILING COVER DOWNROD SETSCREW Figure 21 10. Screw two 1-1/4" threaded studs (provided) into the motor (Figure 22). [. . . ] All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR. What Will Emerson Company Do To Correct Problems: Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. [. . . ]