User manual EMERSON FANS STRUCTURES

[. . . ] Emerson Structures 1/24/05 8:22 AM Page 1 READ AND SAVE THESE INSTRUCTIONS Emerson Fans Designed by STRUCTURES Ceiling Fan Owner's Manual Model Numbers KF200NI00 Brushed Nickel with Black/Brushed Nickel Blades KF200OZ00 Olde Bronze with Black/Teak Blades Net Weight: 22. 1 Lbs. Part No. BP7285 Emerson Structures 1/24/05 8:22 AM Page 2 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner's manual carefully and keep it for future reference. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. [. . . ] Secure the decorative rods to the rod support using three decorative rod screws; do not tighten the rod screws at this time. Rotate the rod support assembly until the decorative rod assemblies are aligned vertically with the downrod DOWNROD CEILING COVER 8 Figure 12 SETSCREW Emerson Structures 1/24/05 8:22 AM Page 9 19. The fan comes with blue, black and white leads that are 80" long. Before installing the fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2" from end of leads. You have now completed the initial assembly of your new ceiling fan. You can now proceed with hanging and wiring your fan. 1. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box (Figure 14). ! WARNING Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. OUTLET BOX TWO SCREWS SUPPLIED WITH OUTLET BOX TAB How to Hang Your Ceiling Fan ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 13). CEILING HANGER BRACKET Figure 14 2. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 15). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 14). AT LEAST 7' FLOOR ! Figure 13 ! WARNING WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. outlet box listed as "Acceptable for Fan Support". ! Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. NOTE: CEILING COVER, SUPPL WIRES AND FAN Y WIRES OMITTED FOR CLARITY. OUTLET BOX WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked "Acceptable for Fan Support", and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. HANGER BRACKET HANGER BALL/ DOWNROD ASSEMBLY Figure 15 ! WARNING To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket. 9 Emerson Structures 1/24/05 8:22 AM Page 10 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ! WARNING Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. CAUTION: To reduce the risk of electrical shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver. [. . . ] All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR. Do To Correct Problems: Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. [. . . ]